One channel multiswitch module EMS-16-R, EMS-16-G and EMS-24-G |
Switch panel optional available |
|||
EMS-16-R for Robbe radio control with 5-pole plug |
|||
EMS-16-G for Graupner radio control with 5-pole plug |
|||
EMS-24-G for Graupner radio control with 5-pole plug |
The one channel multiswitch modules at a glance:
|
Description
The one channel multiswitch module EMS is an extension for RC-control, available with 8 and 12 switches in order to control 16 or 24 additional functions, such as triggering sounds and lights.It is suitable for following BEIER-modules:
It is built into the radio control housing and requires for installation only one free proportional channel. For connection no additional decoder is required.
Due to a special data transmission the EMS is compatible with most 2.4 GHz systems. This transmission is carried out with time division multiplex, which leads to a response time delay of up to 1,4 s.
Each switch has three positions: up - middle - down. With the positions "up" and "down" at least two functions can be controlled. The switches have a pushbutton function, they returning automatically to neutral (middle position). With the memory setting from the sound modules SFR-1, USM-RC-2 and the multiswitch decoder MSD-16 each switching output can be activated/deactivated permanently.
The EMS is available in three different versions.
More information can be found in the operating manual (English).
Technical Data
EMS-16-R | |||
---|---|---|---|
Radio remote control: | Optimal for Robbe/Futaba radios. With reconstruction/external box for all radios suitable. |
||
Supply voltage (from radio): |
3 - 5V DC | ||
Power consumption: | ca. 8 mA | ||
Number of switches: | 8 | ||
Number of switch positions: | 16 (2 at each switch) | ||
Distance between switches horizontal: | 15 mm | ||
Distance between switches vertical: | 15 mm | ||
Size board: | 66 x 32 mm | ||
Required height inside radio: | 26 mm (without switch lever) |
EMS-16-G | |||
---|---|---|---|
Radio remote control: | Optimal for Graupner radios. With reconstruction/external box for all radios suitable. |
||
Supply voltage (from radio): |
3 - 5V DC | ||
Power consumption: | ca. 8 mA | ||
Number of switches: | 8 | ||
Number of switch positions: | 16 (2 at each switch) | ||
Distance between switches horizontal: | 12 mm | ||
Distance between switches vertical: | 15 mm | ||
Size board: | 66 x 47 mm | ||
Required height inside radio: | 26 mm (without switch lever) |
EMS-24-G | |||
---|---|---|---|
Radio remote control: | Optimal for Graupner radios. With reconstruction/external box for all radios suitable. |
||
Supply voltage (from radio): |
3 - 5V DC | ||
Power consumption: | ca. 8 mA | ||
Number of switches: | 12 | ||
Number of switch positions: | 24 (2 at each switch) | ||
Distance between switches horizontal: | 12 mm | ||
Distance between switches vertical: | 15 mm | ||
Size board: | 66 x 47 mm | ||
Required height inside radio: | 26 mm (without switch lever) |
Overview of compatible and not compatible radio remote controls
Sender | External housing necessary | EMS-Type | Compatibility |
---|---|---|---|
Graupner 4014 | no | EMS-16-G EMS-24-G |
|
Graupner mc-19 | no | EMS-16-G EMS-24-G |
|
Graupner mc-22 | no | EMS-16-G EMS-24-G |
|
Graupner mc-24 | no | EMS-16-G EMS-24-G |
|
Graupner mc-32 | no | EMS-16-G EMS-24-G |
|
Graupner mx-10, mx-12, mx-16, mx-20, mx-32 | yes | EMS-16-G EMS-24-G |
1) |
Graupner mz-10, mz-12, mz-18, mz-24 | - | - | 3) |
Robbe F-14 | no | EMS-16-R | |
Robbe FC-16 | no | EMS-16-R | |
Robbe FC-18 | no | EMS-16-R | |
Robbe FX-30 | yes | EMS-16-R | |
Spektrum DX5 | yes | EMS-16-G EMS-24-G |
2) |
Spektrum DX6 | yes | EMS-16-G EMS-24-G |
2) |
Spektrum DX7 | yes | EMS-16-G EMS-24-G |
2) |
FLY SKY FS-T6 | yes | EMS-16-G EMS-24-G |
|
Turnigy 9X | yes | EMS-16-G EMS-24-G |
|
FrSky Taranis QX7 | yes | EMS-16-G EMS-24-G |
|
JETI DC-16 | yes | EMS-16-G EMS-24-G |
Legend:
Compatible (tested) | |
? | Should be compatible (not tested) |
Not compatible | |
1) | At transmitters of the MX-series, there is a feature that should be noted: The EMS module may only be switched on after the transmitter has bootet completly after power on! It still needs a switch installed in the plus line (orange cable) of the EMS, with the EMS can be turned on and off. |
2) | At these radio controls, the switch inputs are not true proportional inputs, but only switching inputs. Therefore, you have to use a channel of a stick for connection of the EMS! This channel can no longer be controlled with the stick. |
3) | Unfortunately, the transmitter encoder voltage of 0,7 V is not enough to operate the EMS processor (at least 2,5 V required). |
Prices
Included in delivery:
|
|
To use the EMS with BEIER-modules you need the latest Sound-Teacher version.
You can download an update with your Sound-Teacher from our homepage.
Customer reviews for this product
03.05.2022 Hans-Hermann aus Suhl: |
Ich habe jetzt den zweiten EMS in Betrieb, diesmal ein EMS24G. Wie schon beim EMS16G gab es NULL Probleme mit den HoTT 2,4GHz Sendern. Die leichte Verzögerung gegenüber dem NMS kann man getrost ignorieren, manche Menschen haben eine viel schlechtere Reaktionszeit. Durch den im Vergleich zu älteren GR Sendern wie der MC24 etwas 'seltsam' gemachten Optionsplatz der MC32 (mit 'Plastikstützen' innen) war der Einbau allerdings etwas fummelig. Hier fehlen die bei Original Graupner Schaltern vorhandenen 'Ringe' an den Schaltern. Ohne diese Ringe funktioniert das nicht, bzw. man zerstört die Schalter beim festziehen der Muttern bzw. sie haben nur eine Abstützung am Rand. Die Graupner Ringe passen aber nicht. Was fehlt ist eigentlich nur eine 'Unterlegscheibe', welche den richtigen Außendurchmesser hat und statt Gegenmutter auf den Schalter kommt. Natürlich stabiler als aus irgendeinem weichen Blech, denn sie stützt ja da Schaltergehäuse. Andererseits darf sie auch nicht zu dick sein, sonst reicht das Gewinde außen nicht mehr aus um den EMS festzuziehen. Das gilt m.W. nur für neuere Sender der MC Reihe. Meine 'Notlösung' war die Verwendung der Zahnscheiben und VIEL Gefühl beim anziehen der Muttern. Der EMS bekam noch einen zum UVR Steckplatz der MC32 passenden JST XH Stecker gecrimpt und dann gab es die bei Beier Produkten problemlose Inbetriebnahme. Klick, läuft! Ich liebe 'Made in Germany'! Großes Kino, Top Qualität, jeden Cent wert! |
To write a new review, please login to your customer account.
Login | Register