output 11 doesn't work anymore
output 11 doesn't work anymore
i think my output 11 is defect.
i connected a smoke generator and flashlight but none of them works.
i connected the smoke generator to output 8 and it works.
has anyone any idea if my outputs 11&12 are defect?
i don't use servo output 1&2
i connected a smoke generator and flashlight but none of them works.
i connected the smoke generator to output 8 and it works.
has anyone any idea if my outputs 11&12 are defect?
i don't use servo output 1&2
- BEIER-Electronic Andy
- Administrator
- Beiträge: 4557
- Registriert: Mi 17. Dez 2008, 07:37
Re: output 11 doesn't work anymore
Please look in the diagnosis (see page 75 in the manual), if you see a green circle when you activate the output 11.
If the output in the diagnosis is green but the output doesn't switch correct, then the output is defect. In the case, send the module to us (or we send a transistor if you can solder SMD).
If the output in the diagnosis is green but the output doesn't switch correct, then the output is defect. In the case, send the module to us (or we send a transistor if you can solder SMD).
Re: output 11 doesn't work anymore
all outputs turn green except output 11
- BEIER-Electronic Andy
- Administrator
- Beiträge: 4557
- Registriert: Mi 17. Dez 2008, 07:37
Re: output 11 doesn't work anymore
Please send me your projectfile (*.usm).
Re: output 11 doesn't work anymore
output 8 is the smokegenerator i set it to motion.
ouput 11 are the flashlights and output 12 is the brake light for my trailer
ouput 11 are the flashlights and output 12 is the brake light for my trailer
- BEIER-Electronic Andy
- Administrator
- Beiträge: 4557
- Registriert: Mi 17. Dez 2008, 07:37
Re: output 11 doesn't work anymore
I've tested your project, and it worked fine.
The diagnosis shows only what the output should do - even with a defect transistor, the circle should become green!
Do you have the datacable K-USB-2?
This is crazy...darentz27 hat geschrieben:all outputs turn green except output 11
The diagnosis shows only what the output should do - even with a defect transistor, the circle should become green!
Do you have the datacable K-USB-2?
Re: output 11 doesn't work anymore
No i don't have the cable
- BEIER-Electronic Andy
- Administrator
- Beiträge: 4557
- Registriert: Mi 17. Dez 2008, 07:37
Re: output 11 doesn't work anymore
Ok, then please send the module to us. We will check and repair it.
Re: output 11 doesn't work anymore
where do i send the module to?
do you have an adress?
except i haven't bought it in your webshop.
I bought it by a dutch company.
should i contact them or can i send my module to you?
do you have an adress?
except i haven't bought it in your webshop.
I bought it by a dutch company.
should i contact them or can i send my module to you?
- BEIER-Electronic Andy
- Administrator
- Beiträge: 4557
- Registriert: Mi 17. Dez 2008, 07:37
Re: output 11 doesn't work anymore
It's better to send it directly to us:
BEIER-Electronic
Winterbacher Straße 52/4
73614 Schorndorf - Weiler
Germany
And please send also the SD card with your project.
BEIER-Electronic
Winterbacher Straße 52/4
73614 Schorndorf - Weiler
Germany
And please send also the SD card with your project.