Interference

Soundmodul für Fahrgeräusche (speziell für RC-Modelle). Der Nachfolger des USM-RC
Scrooge
Beiträge: 16
Registriert: Mi 12. Jun 2013, 20:22

Interference

Beitrag von Scrooge »

Dear All
Faced with the following problem
Recently installed the USM-RC-2
When the USM is not powered my truck runs like a charm and I can control it from any distance
As soon the USM is powered there is interference, and when the model gets 2-3 m away > lights start flashing, horn sounds etc etc :(

USM was at first set-up in EKMFA mode, but is now in Nautic with the NMS-16-G, and this is even worse. Even when sitting right next to the model the blinkers L&R start living their own life. :evil:

1000µF 25V cap hooked up directly at the USM "power IN"; power is taken directly from the batt. leads (sodered and crimped); receiver is powered from the speed controler
Set-up: Transmitter MC12 / Receiver R700 / speed controler Rookie /
An optocoupler is connected, to transmit signals to the trailer over a Vellemen K8023 but this is not under power.
Any sugestions are more than welcome.
Benutzeravatar
BEIER-Electronic Andy
Administrator
Beiträge: 4557
Registriert: Mi 17. Dez 2008, 07:37

Re: Interference

Beitrag von BEIER-Electronic Andy »

Hello Scrooge,

can you test it with another receiver?

The distance between receiver/antenna and speaker/speaker wires is very important. Can you increase the distance?

Do you have this interference when you disconnect the speaker from the USM-RC-2?
Scrooge
Beiträge: 16
Registriert: Mi 12. Jun 2013, 20:22

Re: Interference

Beitrag von Scrooge »

I may have an other receiver hanging around somewhere so will try that shortly, but the fact that with unpowered USM it works fine >>>>>
When testing I have the cab removed from the model and with this also the speaker connector, as the speaker is installed in the cab.
I also had the antenna wire layed-out in diff directions pointing away from the USM.
Benutzeravatar
BEIER-Electronic Andy
Administrator
Beiträge: 4557
Registriert: Mi 17. Dez 2008, 07:37

Re: Interference

Beitrag von BEIER-Electronic Andy »

Scrooge hat geschrieben: but the fact that with unpowered USM it works fine
Yes, but there are some very sensitive receivers which don't like other electronics in their near :cry:
It's just a test, if another receiver has the same problems. After this test, we will see what we can do.
Scaniar500
Beiträge: 4
Registriert: Sa 15. Jun 2013, 22:36

Re: Interference

Beitrag von Scaniar500 »

Hi , i recently buyed the usm rc 2 to . Im facing the exact same problem . I have a futuba fc16 with reciever . Unplug the sound module working fine . When plugged 2 -3m the trucks gets crazy . I noticed when i drive over electric cables in the ground the truck is living his own life dont respond to the controller , wheels turning , sound up , down , horn etc....
Scrooge
Beiträge: 16
Registriert: Mi 12. Jun 2013, 20:22

Re: Interference

Beitrag von Scrooge »

Tried today with anaother receiver (futaba) no change :evil:
Next thing I want to try is to deconnect the optocoupler then see what happens.
Benutzeravatar
BEIER-Electronic Andy
Administrator
Beiträge: 4557
Registriert: Mi 17. Dez 2008, 07:37

Re: Interference

Beitrag von BEIER-Electronic Andy »

@Scaniar500:
What frequency has your FM transmitter?

@Scrooge:
The second receiver has also 72MHz like the R7000?

@both:
Please make some tests:
- Disconnect the speaker connectors directly at the soundmodul (X5, X6) and check if this improves something.
- If possible, please power the USM-RC-2 and/or the receiver with a seperate battery and tell me if this improves the receiving.
Scaniar500
Beiträge: 4
Registriert: Sa 15. Jun 2013, 22:36

Re: Interference

Beitrag von Scaniar500 »

im on 40 mhz channel 83 , i have a robbe futaba FP-R118F 8channel receiver
i removed the speakers directly at the USM-RC 2, no improvements ...
i connect the USM and My speed controller and receiver to different battery's , No luck ... still same problem
Scrooge
Beiträge: 16
Registriert: Mi 12. Jun 2013, 20:22

Re: Interference

Beitrag von Scrooge »

Receiver also on 35 Mhz (used x-tal of my R700 for the test)
=channel 63
Will do the proposed tests but in my case speaker leads are 2-3 cm long (module to connector on strip board) also I just switch on the power of the module, I did not even switch on the sound (= over transmitter)
Scrooge
Beiträge: 16
Registriert: Mi 12. Jun 2013, 20:22

Re: Interference

Beitrag von Scrooge »

BEIER-Electronic hat geschrieben:If possible, please power the USM-RC-2 and/or the receiver with a seperate battery and tell me if this improves the receiving.
2 seperate batt.
Common ground?
Antworten