smoke generator
smoke generator
i've bought a smoke generator and would to connect it to the beier sound module but when i attach it to output 11 nothing happens.
has anyone any idea?when i connect the smoke generator to the + and - from the battery the smoke generator works
has anyone any idea?when i connect the smoke generator to the + and - from the battery the smoke generator works
- marco polo
- Beiträge: 92
- Registriert: Di 26. Okt 2010, 20:45
- Wohnort: holland
- Kontaktdaten:
Re: smoke generator
hallo darentz27
could you tell us wat kind of smoke generator you bought
welke rookgenerator heb je gekocht
how much current does it draw
hoeveel stroom gaat er door
how did you conect it to the usm
hoe heb je hem aangesloten op de usm
how did you program output 11
hoe heb je uitgang 11 geprogrameerd
how do you ativate output 11
hoe bedien je uitgang 11
gr marco polo
could you tell us wat kind of smoke generator you bought
welke rookgenerator heb je gekocht
how much current does it draw
hoeveel stroom gaat er door
how did you conect it to the usm
hoe heb je hem aangesloten op de usm
how did you program output 11
hoe heb je uitgang 11 geprogrameerd
how do you ativate output 11
hoe bedien je uitgang 11
gr marco polo
groeten uit Nederland,
Niets is zeker, en zelfs dat niet.
Niets is zeker, en zelfs dat niet.
Re: smoke generator
http://www.modelshoponline.nl/accessoir ... or-12v-72v
maar dan de 7,2 volt versie.
ik heb uitgang 11 geprogrameerd met in motion en acceleration maar beide werken niet.
En parallel via de esc werkt wel maar moet dan vol gas geven voor een beetje rook dan komt de generator te langzaam op gang
maar dan de 7,2 volt versie.
ik heb uitgang 11 geprogrameerd met in motion en acceleration maar beide werken niet.
En parallel via de esc werkt wel maar moet dan vol gas geven voor een beetje rook dan komt de generator te langzaam op gang
- BEIER-Electronic Andy
- Administrator
- Beiträge: 4557
- Registriert: Mi 17. Dez 2008, 07:37
Re: smoke generator
Hello darentz,
at the output configuration "at accelerating" there is the problem, that the output is only very short active. But at setting "in motion" the smoke generator should normaly work well.
Can you test the output 11 with a LED + resistor? Or try to use a different output for the smoker?
at the output configuration "at accelerating" there is the problem, that the output is only very short active. But at setting "in motion" the smoke generator should normaly work well.
Can you test the output 11 with a LED + resistor? Or try to use a different output for the smoker?
Re: smoke generator
i'll switch the outputs 11 &12 see what happens
- BEIER-Electronic Andy
- Administrator
- Beiträge: 4557
- Registriert: Mi 17. Dez 2008, 07:37
Re: smoke generator
Please try also one from the outputs 1-10 at connector X3.
- marco polo
- Beiträge: 92
- Registriert: Di 26. Okt 2010, 20:45
- Wohnort: holland
- Kontaktdaten:
Re: smoke generator
hallo darentz27
heb je er ook aan gedacht om de intensity op max 100 % te zetten ?
anders anders komt er niet de maximale spanning op de generator
oja wat is de accu spanning die je gebruikt
gr marc
heb je er ook aan gedacht om de intensity op max 100 % te zetten ?
anders anders komt er niet de maximale spanning op de generator
oja wat is de accu spanning die je gebruikt
gr marc
groeten uit Nederland,
Niets is zeker, en zelfs dat niet.
Niets is zeker, en zelfs dat niet.
Re: smoke generator
i've connected the smoke generator on output 5 and it works.i think the outputs 11 &12 are defect because when i connect a led to it the led turns on but doesn't go off if i hit the stick.i use a 7,2 lipo battery.
- BEIER-Electronic Andy
- Administrator
- Beiträge: 4557
- Registriert: Mi 17. Dez 2008, 07:37
Re: smoke generator
Do you use seperate batteries for sound module and speed controller/receiver?
Re: smoke generator
i use the same battery.all the lights worked when i had no smoke generator.do you think there is not enough power to let it all work?Or should i connect the smokegenerator to x1&x2?