Seite 1 von 1

[SOLVED] M3 output?

Verfasst: Di 8. Sep 2026, 23:51
von Hansvg
Hi,
I have programmed SFR-1-D to control a motor via M3, at least I thought ;-)
In "speedcontrol" I selected "left/right" control.
In "servo outputs" I selected Servo3 to follow Prop3.
M3 does not give any output on the connector, while a connected servo on Servo 3 reacts properly to the commands.
What is the difference between M1/M2 and M3/M4 here?
Thanks in advance for any help/suggestions.

Regards, Hans

Re: M3 output?

Verfasst: Mi 9. Sep 2026, 00:37
von Rascal
Hello Hans,
Hansvg hat geschrieben: ↑Di 8. Sep 2026, 23:51In "speedcontrol" I selected "left/right" control.
In "servo outputs" I selected Servo3 to follow Prop3.
M3 does not give any output on the connector, while a connected servo on Servo 3 reacts properly to the commands.
Servos are not related to the motors (M1 to M4), so let's separate the two:
In "servo outputs" I selected Servo3 to follow Prop3.
while a connected servo on Servo 3 reacts properly to the commands.
Ok, that works as expected. :)
In "speedcontrol" I selected "left/right" control.
M3 does not give any output on the connector,
Since you have selected "Control motor output via function 'left' / 'right' you must then configure those functions to a prop channel, Nautic/Multiswitch, EKMFA or Control pad (whichever you prefer to use).

E.g. assign functions "Motor M3 left" and "Motor M3 right" to a prop channel which is connected to the receiver.
(Similar to how you assigned the functions for the additional sounds 1 and 2 to Prop #8.)
What is the difference between M1/M2 and M3/M4 here?
- Current handling (M1/M2: 30A, M3/M4: 2A)
- Mixer only for M1/M2
- M1/M2 only allow proportional control via Prop #1 / Prop #2
- M3/M4 allow proportional control via assignable prop channel or via functions (see above)
- Engine sound (as in main Engine sound) only tied to M1/M2

Think tank or crawler excavator - M1 and M2 are the main motors for track left and right, while M3 or M4 can be used e.g. to turn the turret or cabin.
For a boat/ship with two propellers M1 and M2 can drive those while M3 is e.g. used for a transverse thruster and M4 for a crane, turret, radar etc.

So M1/M2 for the main drive train and M3/M4 for (optional) auxiliary drives and such.

You can find more details in the manual, just search e.g. for "M3" to find the relevant sections.

Re: M3 output?

Verfasst: Mi 9. Sep 2026, 01:02
von Hansvg
Thank you!
Indeed, what I want to do is connect one of the receivers channels to control M3 for a bow thruster.
Proportional control would be great instead of just 100% left/stop/100% right.
I have gone through the manual with all 20 "M3" hits, but was not able to come up with the right solution.
Appreciate your help here!

PS. connecting a servo out was just as diagnostics and that worked :-)

Regards, Hans

Re: M3 output?

Verfasst: Mi 9. Sep 2026, 10:55
von Rascal
Hello Hans,
Indeed, what I want to do is connect one of the receivers channels to control M3 for a bow thruster.
Proportional control would be great instead of just 100% left/stop/100% right.
Select "Control motor output via prop. channel" (instead of "Control motor output via function 'left' / 'right' ") and select the desired prop channel under "Speed vom channel:" from the drop down menu.
I have gone through the manual with all 20 "M3" hits, but was not able to come up with the right solution.
From page 61 Configuration – Speed Controller – Motor M3 + M4:
Control motor via one proportional channel
With this setting the speed of motor M3 and M4 can be controlled proportional and steppless with any SFR-1-D prop. channel.

Re: M3 output?

Verfasst: Mi 9. Sep 2026, 15:34
von Hansvg
Hi Rascal,

Thank you very much for your help. Very much appreciated!
I configured the M3 output as you suggested, and this works :-)
It does however not allow for a % set on the PWM power so I can not drive a 6 volt motor while using 12 volt power supply.
That was my other question in the forum. Or am I missing something.
You can tell I am a beginner with this SFR-1-D and learning ;-)

Regards, Hans

Re: M3 output?

Verfasst: Mi 9. Sep 2026, 20:07
von Rascal
Hansvg hat geschrieben: ↑Mi 9. Sep 2026, 15:34It does however not allow for a % set on the PWM power so I can not drive a 6 volt motor while using 12 volt power supply.
That was my other question in the forum. Or am I missing something.
Well, you can when using the option "Control motor output via function 'left' / 'right' ". It wasn't clear from your other question that you wanted to use it with proportional control.

That being said if your transmitter allows setting servo end points you can use those to limit the voltage on the proportional channel that controls M3.
You can tell I am a beginner with this SFR-1-D and learning ;-)
No worries. :)

Re: M3 output?

Verfasst: Mi 9. Sep 2026, 22:34
von Hansvg
I will try that.
But otherwise it works and why change a winning horse :-)
Next step: sounds and functions.
Eventually Happy Hunter should be complete with a lot of functions.
Thanks again!
Regards, Hans