Seite 1 von 2

No sound

Verfasst: Mo 7. Sep 2026, 18:11
von Torbenkg
Hi.
I am currently installing a USM-RC-3 sound module in a Huey helicopter, but when I test it, there is no sound.
Without the SD card, the green LED stays on continuously, the red LED flashes, and the blue LED stays on continuously. With the SD card inserted, the green LED stays on continuously, and the blue LED turns off after about 4–5 flashes.
The USM-RC-3 sound module has its own 7.4V battery, and the module is connected to a receiver (MSH Brain2), which is powered by the ESC's built-in BEC.
The USM-RC-3 is connected via Prop#1 to the Brain2 using the signal and GND cables.
Can anyone tell me what is wrong? :?:
Thanks in advance

Torben

Re: No sound

Verfasst: Mo 7. Sep 2026, 21:21
von Rascal
Hello Torben,
Torbenkg hat geschrieben: ↑Mo 7. Sep 2026, 18:11I am currently installing a USM-RC-3 sound module in a Huey helicopter, but when I test it, there is no sound.
Please upload the current configuration (*.usm-rc-3) for us to check.
Without the SD card, the green LED stays on continuously, the red LED flashes, and the blue LED stays on continuously. With the SD card inserted, the green LED stays on continuously, and the blue LED turns off after about 4–5 flashes.
The SD card must be inserted for the module to work, and the SD card must contain a valid configuration, i.e. a project made with the Sound-Teacher.

If the card was deleted/formatted/replaced insert the SD card into the PC and save a project to the SD card. Then eject and put back into the module.

(Make sure to save the project to the PC, too, in case the card gets lost or broken. Also back-up all projects to an external device to safeguard against a broken or otherwise unusable PC.)
The USM-RC-3 sound module has its own 7.4V battery, and the module is connected to a receiver (MSH Brain2), which is powered by the ESC's built-in BEC.
The USM-RC-3 is connected via Prop#1 to the Brain2 using the signal and GND cables.
Can anyone tell me what is wrong? :?:
Try connecting the minus of the USM-RC3 battery with the minus of the ESC battery, although I think this may be a configuration issue.

Re: No sound

Verfasst: Di 8. Sep 2026, 17:18
von Torbenkg
I have ordered a data cable and I will send the file to you as soon I have it.
Thanks

Re: No sound

Verfasst: Di 8. Sep 2026, 17:55
von Rascal
Hello Torben,

you don't need a data cable for the project file. You should have this on your PC, if not you can use the import function to retrieve it from the SD card (card must be inserted into the PC):

viewtopic.php?p=21146#p21146

Re: No sound

Verfasst: Di 8. Sep 2026, 20:31
von Torbenkg
Hi
I have attached the file.
Thanks in advance

Re: No sound

Verfasst: Di 8. Sep 2026, 21:57
von Rascal
Thanks, that's the correct file.

I notice that you have configured the function "Engine sound on/off" using 3 different methods:
  • Automatically when applying throttle
  • Using the respective function on Prop #4
  • Using input 1 (X1/3)
Generally I recommend configuring & using only one method to avoid any confusion.

However since all three are currently configured have you tried all of them? If yes, did any of them work?

If not the easiest would probably be applying battery minus to the input X1/3. Any sound then?

If not:
Check the battery. The option "At undervoltage: Turn sound off" (as well as "At undervoltage: Turn outputs off") is activated. Thus if the battery voltage is below the threshold no sound will be played.

Since you have a helicopter I assume the ESC does not have a reverse function and Neutral / zero throttle is stick down (not middle). The USM-RC-3 reads Prop #1 and #2 at power up and it should adjust the sound diagram automatically.
If possible I would like to take a look at that, thus please import the project from the SD card (see link in my previous post) and upload the *.usm-rc-3 file here.

If you get the data cable in the mean time you can also add a diagnostic (say about 30 seconds max, moving the throttle stick up and down a few times). Then we can see if any signal comes in at all on Prop #1 and the neutral value of that channel.

(You can actually connect the red wire between the Brain2 and Prop #1, too - it does not harm the USM-RC-3 since the center pin isn't connected to the circuitry of the USM.)

Re: No sound

Verfasst: Mi 9. Sep 2026, 16:54
von Torbenkg
I have tried to start over with a new project on the sd card. The red wire is now in place. Battery full powered.
Attached is a new usm-file and a picture of my radio-setup. The sound module is connected to ch4 on the receiver.
But still no sound.
Thanks for your help

Re: No sound

Verfasst: Mi 9. Sep 2026, 19:05
von Hasi
Maybe a dumb question, but since it is not mentioned:

What speaker do you use, if any?

Maybe the speaker is the problem - is it possible for you to test with another one?

Re: No sound

Verfasst: Mi 9. Sep 2026, 20:16
von Rascal
Hello Torben,
Torbenkg hat geschrieben: ↑Mi 9. Sep 2026, 16:54Attached is a new usm-file and a picture of my radio-setup. The sound module is connected to ch4 on the receiver.
But still no sound.
Please check the speaker as suggested by Hasi.

What exactly is CH4 - a slave mix to throttle on CH1, or are you just trying a stick on CH4 to test the sound module?

Have you tried a servo on CH4? Does it move when you move the stick? If not CH4 is the problem.

Re: No sound

Verfasst: Sa 12. Sep 2026, 15:44
von Torbenkg
It's working. Sound on 😊
I moved the cable from usm to ch2 on the receiver
Thanks for your help