Help needed in connecting my sound module
Verfasst: So 17. Sep 2023, 23:35
Greetings everyone!
I have a Beier USM-RC-3 that I am trying to connect all my electronics to, to run a RC conversion of an Italeri S-100 Schnellboot. I have a Robbe Futaba FC-16 Boat ’n Truck transmitter, that has been converted to 2,4Ghz, and has both a Robbe Multiswitch and a Robbe Multiprop module inside, and the navy twin stick module.
The receiver I am running is a Jeti Duplex R9.
I have made quite a lot of functions in my model functional, but am very confused on how to properly connect everything.
My set-up:
• 1x Beier USM-RC-3
• 1x AKL-8-W module for connecting LED’s (maybe unneeded because of supplied ribbon cable)
• 9x 3.3V SMD LED’s
- 2 white lights for deck illumination
- 1 white light inside the bridge
- 1 red light inside the bridge
- 1 white spotlight for dropping depth charges
- 4 navigation lights (red, green, white front, white rear)
• 3x Hobbywing Quicrun 10BL60 brushless speed controllers, all with BEC
- 1 center motor
- 2 side motors, individually operable for better maneuverability
• 3x servo’s for deck guns
• 1x 4ohm speaker (Visaton FRWS 5)
I am planning on powering the model with a Gens ace 11.1V 8000mAh Lipo battery
Functions I am looking for:
• I am looking to power my center motor using the right stick on my transmitter, and using the two sticks of the Navy module to power the outer motors separately.
• I’d like to have the center ESC be engine #1 for the sound module, and would like to somehow have both outer ESC’s be responsible for the sound of engine #2. Unfortunately it is not possible to set a third engine in the module. Can I use a V-mixer to mix the signal of the two ESC’s and then feed this to the Beier module as a single signal? I am sure using a simple Y-cable here will cause problems with the ESC’s, and just connecting one of the outer ESC’s will make everything quiet when only using the ESC that is not connected.
• The 3 servo’s for the deck guns I am trying to steer using my Multiprop module.
• The LED’s I want to switch using the Multiswitch module ( Nav lights on/off, spotlight on/off, bridge light switch between red/off/white, and the deck lights on/off), and I also want some sound functions on the remaining Multiswitch channels.
Questions:
I have looked through the manual of the Beier module and every time I think I understand what is going on, something new pops up and I get confused again. Can anyone assist me with how to properly connect everything?
1. Which ports on the Beier module need to connect to which function on my receiver?
2. How many patch cables do I need in total?
3. Do the ESC’s plug into the Beier module and then the Beier Module connects to the receiver with patch cables, or do I use Y-cables to connect the ESC’s and the Beier module in parallel?
4. Will the engine sounds even work with brushless motors or is this function reserved for brushed motors?
5. Which ports should I connect my LED’s to? I believe I only have 8 connections available, can I connect the two deck lights in parallel using the same resistor I use for all the other LED’s? Which cables are postive, and which are negative?
6. Can I use both a Multiswitch and Multiprop module at the same time, or just one of the two? I have a separate Multiprop decoder if necessary, but prefer to have everything function from the Beier module.
I have the AKL-8-W module for connecting the LED’s to, but I noticed there is a different ribbon cable already supplied with the USM-RC-3 module. I assume these do the exact same, and I can just avoid the AKL-8-W module by soldering the LED’s to the supplied ribbon cable, provided I use the proper resistors? If this is the case, which cables are positive, and which are negative?
I have several other functions in my model, but I can run these directly from the receiver without bothering with the Beier module, so I have left these out for now.
I already know that two of my ESC’s need to have the positive wire cut to prevent issues, and I apparantly need to somehow power the Beier module separate from the rest of the electronics using the supplied breaker. I think this just means connecting the positive and negative wires parallel to the battery wires that feed the ESC’s?
I know I am asking a lot. Even if only some of my questions are answered it will be a step in the right direction and I will be very happy!
I have a Beier USM-RC-3 that I am trying to connect all my electronics to, to run a RC conversion of an Italeri S-100 Schnellboot. I have a Robbe Futaba FC-16 Boat ’n Truck transmitter, that has been converted to 2,4Ghz, and has both a Robbe Multiswitch and a Robbe Multiprop module inside, and the navy twin stick module.
The receiver I am running is a Jeti Duplex R9.
I have made quite a lot of functions in my model functional, but am very confused on how to properly connect everything.
My set-up:
• 1x Beier USM-RC-3
• 1x AKL-8-W module for connecting LED’s (maybe unneeded because of supplied ribbon cable)
• 9x 3.3V SMD LED’s
- 2 white lights for deck illumination
- 1 white light inside the bridge
- 1 red light inside the bridge
- 1 white spotlight for dropping depth charges
- 4 navigation lights (red, green, white front, white rear)
• 3x Hobbywing Quicrun 10BL60 brushless speed controllers, all with BEC
- 1 center motor
- 2 side motors, individually operable for better maneuverability
• 3x servo’s for deck guns
• 1x 4ohm speaker (Visaton FRWS 5)
I am planning on powering the model with a Gens ace 11.1V 8000mAh Lipo battery
Functions I am looking for:
• I am looking to power my center motor using the right stick on my transmitter, and using the two sticks of the Navy module to power the outer motors separately.
• I’d like to have the center ESC be engine #1 for the sound module, and would like to somehow have both outer ESC’s be responsible for the sound of engine #2. Unfortunately it is not possible to set a third engine in the module. Can I use a V-mixer to mix the signal of the two ESC’s and then feed this to the Beier module as a single signal? I am sure using a simple Y-cable here will cause problems with the ESC’s, and just connecting one of the outer ESC’s will make everything quiet when only using the ESC that is not connected.
• The 3 servo’s for the deck guns I am trying to steer using my Multiprop module.
• The LED’s I want to switch using the Multiswitch module ( Nav lights on/off, spotlight on/off, bridge light switch between red/off/white, and the deck lights on/off), and I also want some sound functions on the remaining Multiswitch channels.
Questions:
I have looked through the manual of the Beier module and every time I think I understand what is going on, something new pops up and I get confused again. Can anyone assist me with how to properly connect everything?
1. Which ports on the Beier module need to connect to which function on my receiver?
2. How many patch cables do I need in total?
3. Do the ESC’s plug into the Beier module and then the Beier Module connects to the receiver with patch cables, or do I use Y-cables to connect the ESC’s and the Beier module in parallel?
4. Will the engine sounds even work with brushless motors or is this function reserved for brushed motors?
5. Which ports should I connect my LED’s to? I believe I only have 8 connections available, can I connect the two deck lights in parallel using the same resistor I use for all the other LED’s? Which cables are postive, and which are negative?
6. Can I use both a Multiswitch and Multiprop module at the same time, or just one of the two? I have a separate Multiprop decoder if necessary, but prefer to have everything function from the Beier module.
I have the AKL-8-W module for connecting the LED’s to, but I noticed there is a different ribbon cable already supplied with the USM-RC-3 module. I assume these do the exact same, and I can just avoid the AKL-8-W module by soldering the LED’s to the supplied ribbon cable, provided I use the proper resistors? If this is the case, which cables are positive, and which are negative?
I have several other functions in my model, but I can run these directly from the receiver without bothering with the Beier module, so I have left these out for now.
I already know that two of my ESC’s need to have the positive wire cut to prevent issues, and I apparantly need to somehow power the Beier module separate from the rest of the electronics using the supplied breaker. I think this just means connecting the positive and negative wires parallel to the battery wires that feed the ESC’s?
I know I am asking a lot. Even if only some of my questions are answered it will be a step in the right direction and I will be very happy!