Greetings everyone!
I have a Beier USM-RC-3 that I am trying to connect all my electronics to, to run a RC conversion of an Italeri S-100 Schnellboot. I have a Robbe Futaba FC-16 Boat ’n Truck transmitter, that has been converted to 2,4Ghz, and has both a Robbe Multiswitch and a Robbe Multiprop module inside, and the navy twin stick module.
The receiver I am running is a Jeti Duplex R9.
I have made quite a lot of functions in my model functional, but am very confused on how to properly connect everything.
My set-up:
• 1x Beier USM-RC-3
• 1x AKL-8-W module for connecting LED’s (maybe unneeded because of supplied ribbon cable)
• 9x 3.3V SMD LED’s
- 2 white lights for deck illumination
- 1 white light inside the bridge
- 1 red light inside the bridge
- 1 white spotlight for dropping depth charges
- 4 navigation lights (red, green, white front, white rear)
• 3x Hobbywing Quicrun 10BL60 brushless speed controllers, all with BEC
- 1 center motor
- 2 side motors, individually operable for better maneuverability
• 3x servo’s for deck guns
• 1x 4ohm speaker (Visaton FRWS 5)
I am planning on powering the model with a Gens ace 11.1V 8000mAh Lipo battery
Functions I am looking for:
• I am looking to power my center motor using the right stick on my transmitter, and using the two sticks of the Navy module to power the outer motors separately.
• I’d like to have the center ESC be engine #1 for the sound module, and would like to somehow have both outer ESC’s be responsible for the sound of engine #2. Unfortunately it is not possible to set a third engine in the module. Can I use a V-mixer to mix the signal of the two ESC’s and then feed this to the Beier module as a single signal? I am sure using a simple Y-cable here will cause problems with the ESC’s, and just connecting one of the outer ESC’s will make everything quiet when only using the ESC that is not connected.
• The 3 servo’s for the deck guns I am trying to steer using my Multiprop module.
• The LED’s I want to switch using the Multiswitch module ( Nav lights on/off, spotlight on/off, bridge light switch between red/off/white, and the deck lights on/off), and I also want some sound functions on the remaining Multiswitch channels.
Questions:
I have looked through the manual of the Beier module and every time I think I understand what is going on, something new pops up and I get confused again. Can anyone assist me with how to properly connect everything?
1. Which ports on the Beier module need to connect to which function on my receiver?
2. How many patch cables do I need in total?
3. Do the ESC’s plug into the Beier module and then the Beier Module connects to the receiver with patch cables, or do I use Y-cables to connect the ESC’s and the Beier module in parallel?
4. Will the engine sounds even work with brushless motors or is this function reserved for brushed motors?
5. Which ports should I connect my LED’s to? I believe I only have 8 connections available, can I connect the two deck lights in parallel using the same resistor I use for all the other LED’s? Which cables are postive, and which are negative?
6. Can I use both a Multiswitch and Multiprop module at the same time, or just one of the two? I have a separate Multiprop decoder if necessary, but prefer to have everything function from the Beier module.
I have the AKL-8-W module for connecting the LED’s to, but I noticed there is a different ribbon cable already supplied with the USM-RC-3 module. I assume these do the exact same, and I can just avoid the AKL-8-W module by soldering the LED’s to the supplied ribbon cable, provided I use the proper resistors? If this is the case, which cables are positive, and which are negative?
I have several other functions in my model, but I can run these directly from the receiver without bothering with the Beier module, so I have left these out for now.
I already know that two of my ESC’s need to have the positive wire cut to prevent issues, and I apparantly need to somehow power the Beier module separate from the rest of the electronics using the supplied breaker. I think this just means connecting the positive and negative wires parallel to the battery wires that feed the ESC’s?
I know I am asking a lot. Even if only some of my questions are answered it will be a step in the right direction and I will be very happy!
Help needed in connecting my sound module
Re: Help needed in connecting my sound module
Hello Danny,
- Connect the outer ESCs to Prop #1 and #2, and activate the "2 motors for engine sound" option; this will play the Engine sound (i.e. engine sound #1).
- Connect the center ESC's receiver channel to Prop #4 via a Y-cable and select that prop channel as "Speed from channel:" under Engine sound 2.
- Assign the soundfiles to Engine sound and Engine sound 2 (same or different files, as per your preference).
Alternatively forget the Multiprop module and instead connect the servos to the USM's servo outpus for turning the guns to up to 4 positions each. With function sequences you can concert them together for aquiring a specific "target" and when in position play a shot sound, and if they are equipped for it trigger a LED for the muzzle flash, too.
Suggestion: Make a plan how you want to utilize the prop channels on the USM, i.e. which channel does what exactly, and then it should be quite simple to figure out the connection. E.g. if Prop #3 is assigned to the Multiswitch module then it needs to connect to the receiver channel that carries the multiswitch signal, which can only be 7 or 8.
Does your transmitter have the sliders installed, and if yes are they connected to channels 5 and 6?
Do you want to use direct volume control (see pages 29 & 69 in the manual).
Outputs switch negative while the black & white cables carry battery voltage (+). See pages 10 & 19 in the manual.
If you will use the AKL-8-W please refer to this manual.
Connecting two LEDs in parallel with one resistor may work if the LEDs are of the same type and have tight tolerances, however this is generally not recommended. If one LED goes faulty or becomes disconnected (cable break or such) the other one will be subjected to double the current and may die sooner than later. Each LED should therefore have it's own resistor when connected in parallel.
However you may consider to wire them in series if the forward voltage of the LEDs added together does not exceed the operating voltage (= battery voltage). A white LED has a forward voltage of 3 to 4V, so you are still well below the 11,1V of the battery when two of them are connected in series. Red/green/yellow can even work with 3-4 LEDs in series.
Calculate the resistor value as follows: R = (11,1 - (LEDfv * #ofLEDs)) / LEDcurrent
This actually reduces current consumption but if one LED fails they will all be dark. Then again LEDs will last "forever" if you operate them within their specifications, so I don't see this as a problem.
There is a work-around for that:
- Connect the outer ESCs to Prop #1 and #2, and activate the "2 motors for engine sound" option; this will play the Engine sound (i.e. engine sound #1).
- Connect the center ESC's receiver channel to Prop #4 via a Y-cable and select that prop channel as "Speed from channel:" under Engine sound 2.
- Assign the soundfiles to Engine sound and Engine sound 2 (same or different files, as per your preference).
Yes, you can also use V-mixer and use Prop #1 and #2 only for throttle signals. This will free a prop channel on the USM but occupy an additional channel on the transmitter & receiver.Can I use a V-mixer to mix the signal of the two ESC’s and then feed this to the Beier module as a single signal? I am sure using a simple Y-cable here will cause problems with the ESC’s, and just connecting one of the outer ESC’s will make everything quiet when only using the ESC that is not connected.
If you want to use the Multiprop module you will need the matching Robbe decoder. The USM can not make use of the entire prop-signal range, any potentiometer on the Multiprop module will just be able to trigger a function at the most left and right position (like any on-off-on switch on the Multiswitch module would do).• The 3 servo’s for the deck guns I am trying to steer using my Multiprop module.
Alternatively forget the Multiprop module and instead connect the servos to the USM's servo outpus for turning the guns to up to 4 positions each. With function sequences you can concert them together for aquiring a specific "target" and when in position play a shot sound, and if they are equipped for it trigger a LED for the muzzle flash, too.
That should be no problem.• The LED’s I want to switch using the Multiswitch module ( Nav lights on/off, spotlight on/off, bridge light switch between red/off/white, and the deck lights on/off), and I also want some sound functions on the remaining Multiswitch channels.
That depends how throttle, multiswitch(es), control channels (for sound and light) and mixers are assigned on your receiver, as well if you want to use some channel(s) for direct servo control and/or direct volume control (requires a potentiometer / slider).1. Which ports on the Beier module need to connect to which function on my receiver?
Suggestion: Make a plan how you want to utilize the prop channels on the USM, i.e. which channel does what exactly, and then it should be quite simple to figure out the connection. E.g. if Prop #3 is assigned to the Multiswitch module then it needs to connect to the receiver channel that carries the multiswitch signal, which can only be 7 or 8.
Does your transmitter have the sliders installed, and if yes are they connected to channels 5 and 6?
Do you want to use direct volume control (see pages 29 & 69 in the manual).
At least 5, though if you want to utilize the module fully I think it will be 7 to 8 - depending if the Y-cable for the center ESC is required, or if you use a mixer instead.2. How many patch cables do I need in total?
For Prop #1 and #2 you can plug the ESC cable into the USM and connect to the receiver with patch cables. The pins of X2/1 and X2/2 are duplicated and work exactly like a Y-cable. See page 10 in the manual.3. Do the ESC’s plug into the Beier module and then the Beier Module connects to the receiver with patch cables, or do I use Y-cables to connect the ESC’s and the Beier module in parallel?
It will work with any kind of motor since the signal for the engine sound comes directly from the receiver, as long as the module is running in digital mode. See pages 7 to 10 in the manual.4. Will the engine sounds even work with brushless motors or is this function reserved for brushed motors?
The USM-RC-3 has a total of 17 outputs. Output 17 is a high-current output (max. 3A) and normally used for a smoker or other high current devices, though it can also be used to switch other loads, including a single LED.5. Which ports should I connect my LED’s to? I believe I only have 8 connections available, can I connect the two deck lights in parallel using the same resistor I use for all the other LED’s? Which cables are postive, and which are negative?
Outputs switch negative while the black & white cables carry battery voltage (+). See pages 10 & 19 in the manual.
If you will use the AKL-8-W please refer to this manual.
Connecting two LEDs in parallel with one resistor may work if the LEDs are of the same type and have tight tolerances, however this is generally not recommended. If one LED goes faulty or becomes disconnected (cable break or such) the other one will be subjected to double the current and may die sooner than later. Each LED should therefore have it's own resistor when connected in parallel.
However you may consider to wire them in series if the forward voltage of the LEDs added together does not exceed the operating voltage (= battery voltage). A white LED has a forward voltage of 3 to 4V, so you are still well below the 11,1V of the battery when two of them are connected in series. Red/green/yellow can even work with 3-4 LEDs in series.
Calculate the resistor value as follows: R = (11,1 - (LEDfv * #ofLEDs)) / LEDcurrent
This actually reduces current consumption but if one LED fails they will all be dark. Then again LEDs will last "forever" if you operate them within their specifications, so I don't see this as a problem.
The USM is capable of decoding 2 such modules (on Prop #3 and/or Prop #4), but as mentioned above connecting the Multiprop module to the USM will probably not be of much use.6. Can I use both a Multiswitch and Multiprop module at the same time, or just one of the two? I have a separate Multiprop decoder if necessary, but prefer to have everything function from the Beier module.
Yes.I have the AKL-8-W module for connecting the LED’s to, but I noticed there is a different ribbon cable already supplied with the USM-RC-3 module. I assume these do the exact same, and I can just avoid the AKL-8-W module by soldering the LED’s to the supplied ribbon cable, provided I use the proper resistors?
See above (also pages 10 & 19 of the manual).If this is the case, which cables are positive, and which are negative?
Yes. If you decide to use a seperate battery for the USM ensure that you connect the negative poles of the batteries via a dedicated cable.I already know that two of my ESC’s need to have the positive wire cut to prevent issues, and I apparantly need to somehow power the Beier module separate from the rest of the electronics using the supplied breaker. I think this just means connecting the positive and negative wires parallel to the battery wires that feed the ESC’s?
No worries, that's what this forum is for.I know I am asking a lot. Even if only some of my questions are answered it will be a step in the right direction and I will be very happy!
Re: Help needed in connecting my sound module
Thank you so much, your post has helped me understand how this module works!
My preferred setup on the transmitter is as follows:
Right stick (ch. 1 & 2): rudder and center throttle
Twin Navy sticks (ch. 3 & 4): Throttle left and right
Linear slider left (ch. 5): Volume control
Linear slider right (ch. 6): Activating Lürssen Effekt rudders (outer rudders rotate outwards slightly while still moving with the main rudder)
Multiswitch (ch. 7): Lights and sound effects
Multiprop (ch. 8): moving guns
I believe the attached schematic allows for this setup. I just need to use 5 patch cables, 2 Y-cables, one V-mixer, and a Multiprop decoder, and after that I can arrange everything in the software. The first 8 LED's I will power using the supplied ribbon cable, and a two-pin JST connector for the 9th remaining LED. I just need to find which pinouts to use, but this shouldn't be an issue.
Thanks again for your help!
My preferred setup on the transmitter is as follows:
Right stick (ch. 1 & 2): rudder and center throttle
Twin Navy sticks (ch. 3 & 4): Throttle left and right
Linear slider left (ch. 5): Volume control
Linear slider right (ch. 6): Activating Lürssen Effekt rudders (outer rudders rotate outwards slightly while still moving with the main rudder)
Multiswitch (ch. 7): Lights and sound effects
Multiprop (ch. 8): moving guns
I believe the attached schematic allows for this setup. I just need to use 5 patch cables, 2 Y-cables, one V-mixer, and a Multiprop decoder, and after that I can arrange everything in the software. The first 8 LED's I will power using the supplied ribbon cable, and a two-pin JST connector for the 9th remaining LED. I just need to find which pinouts to use, but this shouldn't be an issue.
Thanks again for your help!
- Dateianhänge
-
- wiring.png (124.44 KiB) 4415 mal betrachtet
Re: Help needed in connecting my sound module
Hello Danny,
glad to be of help.
Your schematic looks good, though I would also connect the negative wire to ESC L & R. Firstly the connector at the USM port will have a tighter fit (less risk of shaking loose) and secondly it provides an additional ground connection.
glad to be of help.
Your schematic looks good, though I would also connect the negative wire to ESC L & R. Firstly the connector at the USM port will have a tighter fit (less risk of shaking loose) and secondly it provides an additional ground connection.
Output 9 isn't close to the + Pin, you may consider changing to output 15 or 16 instead for using the 2-pin JST connector. See page 9 in the manual for the pinout.and a two-pin JST connector for the 9th remaining LED
Re: Help needed in connecting my sound module
Hi Rascal,
Thanks for your quick reply.
Yes, I was already planning on using the negative wires for the ESC's as well, I did not write it on the schematic correctly. I wrote signal only because I am cutting the red wire, but of course the black wire should be connected as well.
As for switching pin 9 to pin 15 or 16, will do!
Thanks for your quick reply.
Yes, I was already planning on using the negative wires for the ESC's as well, I did not write it on the schematic correctly. I wrote signal only because I am cutting the red wire, but of course the black wire should be connected as well.
As for switching pin 9 to pin 15 or 16, will do!