Power switch

Fahrtregler für RC-Trucks und andere Fahrzeuge
Benutzeravatar
micwic
Beiträge: 19
Registriert: Sa 13. Aug 2011, 17:06
Wohnort: Dalbyneder, Denmark
Kontaktdaten:

Power switch

Beitrag von micwic »

May I suggest a relay controlled main circuit breaker on the UFR 1230, when it comes to trucks,
many are so tight constructed that you can not immediately get to the battery and disconnect the power at this place when needed.
you might very well mount a switch on the main cable, but where do I find a switch that can withstand 60A and at the
same time is small enough to hide on the model.
My solution is probably to install a relay from a car, but space is scarce and it is not the optimal solution,
Servonaut has a built-in relay-controlled circuit breaker switch on the M20 + ESC.
I could of course use servonaut M20 + just as a relay but this is just 20A

My point is that it is not advisable to allow the model to stay turned on for a full day, we are some who talk more than we drive our trucks :D
and if I turn off the transmitter the model goes into failsafe and consume even more power by braking
I have not been able to find any information regarding the UFR 1230 enters hibernate at x number of minutes without use or something similar
Benutzeravatar
Oldchap
Beiträge: 1146
Registriert: Do 10. Mär 2011, 14:13
Wohnort: Raum Fürth / Bayern

Re: Power switch

Beitrag von Oldchap »

Hello,

in my opinion a main circuit breaker is not a function of an esc. A main circuit breaker should be installed next to the battery, before any power consumpting part like receiver, UFR, -RC2 and so on can use power. A model consuming 60 A will have space enough for a bi-stable relais deep in its body close to the battery, which ist controlled by 2 simple and very small NO pushbuttons, because it needs only a few mA, but controls 100 A and more. It needs quite no current when not pressing a button, therefore it can last months and years in the OFF position without damaging battery.
Gruß

Gerhard
_________________
Panzermodelle 1:6
Benutzeravatar
micwic
Beiträge: 19
Registriert: Sa 13. Aug 2011, 17:06
Wohnort: Dalbyneder, Denmark
Kontaktdaten:

Re: Power switch

Beitrag von micwic »

Thank you Oldchap, do you by any chance have a link to a suitable relay for use with 2S Lipo.

I've never used a relay in my RC trucks but it sounds like the right solution.

Since I only use Lipo batteries there are no needed for long-term storage with the batteries
installed in the model, they are always removed after use and always charged outside the model
Benutzeravatar
Oldchap
Beiträge: 1146
Registriert: Do 10. Mär 2011, 14:13
Wohnort: Raum Fürth / Bayern

Re: Power switch

Beitrag von Oldchap »

Hello Michael,

unfortunately I don't have a suitable link, because my relais work with 24 V. Perhaps this one will work down to 7,4 V (2 x LiPo):

http://images.google.de/imgres?imgurl=h ... gQ9QEIXzAC
Gruß

Gerhard
_________________
Panzermodelle 1:6
Benutzeravatar
micwic
Beiträge: 19
Registriert: Sa 13. Aug 2011, 17:06
Wohnort: Dalbyneder, Denmark
Kontaktdaten:

Re: Power switch

Beitrag von micwic »

Hi Oldchap

unfortunately minimum voltage 9V on this, I keep searching, Thank you
Rascal
Beiträge: 4113
Registriert: Do 9. Okt 2014, 01:31

Re: Power switch

Beitrag von Rascal »

For 7,2 - 7,4V batteries you will need a 6V relay since the voltage will drop below those values during use (discharge). However I think such a product will be difficult to find.

You could take a gamble with the following that is rated 6,5-16V (switches 12VDC/60A momentarily and 50A continuous): Relais 704 T
Benutzeravatar
micwic
Beiträge: 19
Registriert: Sa 13. Aug 2011, 17:06
Wohnort: Dalbyneder, Denmark
Kontaktdaten:

Re: Power switch

Beitrag von micwic »

Super, thank you Rascal I´ll try this and if it won't work I´ll build one myself
Benutzeravatar
micwic
Beiträge: 19
Registriert: Sa 13. Aug 2011, 17:06
Wohnort: Dalbyneder, Denmark
Kontaktdaten:

Re: Power switch

Beitrag von micwic »

Building one myself
13441540_10209412582702618_1586278674_o.jpg
13441540_10209412582702618_1586278674_o.jpg (169.83 KiB) 6930 mal betrachtet
13441540_10209411792802871_2070781039_o.jpg
13441540_10209411792802871_2070781039_o.jpg (51.62 KiB) 6930 mal betrachtet
Rascal
Beiträge: 4113
Registriert: Do 9. Okt 2014, 01:31

Re: Power switch

Beitrag von Rascal »

Is that the UFR on the top, done by reverse engineering? :mrgreen: :mrgreen:
Benutzeravatar
micwic
Beiträge: 19
Registriert: Sa 13. Aug 2011, 17:06
Wohnort: Dalbyneder, Denmark
Kontaktdaten:

Re: Power switch

Beitrag von micwic »

what ever it takes I will do it, this will be able to power down everything from my transmitter except power for one of my reciever I will need this to turn it back on again
Antworten