USM-RC-2 Think I may have waisted my money
USM-RC-2 Think I may have waisted my money
I hate to say it but I think I may have wasted my money on this sound card. I bought this sound unit because I have a RC4WD Loader and wanted a more authentic sound than the cheap China version that comes with the machine.
Having said that, I have spent no less than 20hrs trying to program the card and have yet to get it to work. For less money I could have purchased other brands and they are plug and play. I really want this card to work but can not get it to play, the best I have is the engine starting but then shuts off and does not run, in addition the sound is sporadic on start up.
I have looked on the site for sound clips but am surprised that there are so few to choose from, Is it possible I looking in the wrong area?
Please Please Please Please, can someone help in getting my card to work and make sound. It would be so appreciated.
Having said that, I have spent no less than 20hrs trying to program the card and have yet to get it to work. For less money I could have purchased other brands and they are plug and play. I really want this card to work but can not get it to play, the best I have is the engine starting but then shuts off and does not run, in addition the sound is sporadic on start up.
I have looked on the site for sound clips but am surprised that there are so few to choose from, Is it possible I looking in the wrong area?
Please Please Please Please, can someone help in getting my card to work and make sound. It would be so appreciated.
Re: USM-RC-2 Think I may have waisted my money
Well, maybe you start with the basics like the engine sound, for which you should describe your setup and configuration in detail. So tell us what RC system you use, how the USM is connected, which channel is for what purpose and how do you want to activate the different functions (prop channel settings, EKMFA mode, Nautic Module etc.)
You could also upload your project file and the diagnostic result (read the manual).
You could also upload your project file and the diagnostic result (read the manual).
Re: USM-RC-2 Think I may have waisted my money
Rascal,
Thanks for responding, I would like to use it in my RC4WD Loader. I will use my Spektrum Dx18 to operate the controls. I have been building RC trucks for about 5 years now and have built almost 50 custom rigs several scratch built, I like to think I have a good understanding of electronics and most of my builds are involved with LED's as well as several functions like booms, lifts or what ever the build suits.
I was interested in the Beier unit as it has the ability to have sounds different than the run of the mill Servonaut or Tamiya MFU.
So having said that I have started a project, picked the start sound, idle sound, run sound, door open close sound, shut down sound and loaded them into the program. Part of my difficulty is I don't see in the operation manual a real DO THIS task list, there seems to be a lot of you can do this but I don't know what actually needs to be done to work. So I loaded the program to the SD card, hooked up the control on my bench with battery, ESC, servos and speaker. I switched everything on, hit the start engine switch and it makes a start sound that breaks up but does not idle or do anything past that. When I move the rudder control the horn plays dixe type horn which is weird because I downloaded a Kenworth horn.
All I really want it to do is door open close, start, idle, run with ESC, shutdown. Simple in my mind but cant get it to do it. And it seems that there should be more sounds available, I thought on the CD there were more sounds to choose from, unfortunately I didn't buy the CD this time.
Thanks for responding, I would like to use it in my RC4WD Loader. I will use my Spektrum Dx18 to operate the controls. I have been building RC trucks for about 5 years now and have built almost 50 custom rigs several scratch built, I like to think I have a good understanding of electronics and most of my builds are involved with LED's as well as several functions like booms, lifts or what ever the build suits.
I was interested in the Beier unit as it has the ability to have sounds different than the run of the mill Servonaut or Tamiya MFU.
So having said that I have started a project, picked the start sound, idle sound, run sound, door open close sound, shut down sound and loaded them into the program. Part of my difficulty is I don't see in the operation manual a real DO THIS task list, there seems to be a lot of you can do this but I don't know what actually needs to be done to work. So I loaded the program to the SD card, hooked up the control on my bench with battery, ESC, servos and speaker. I switched everything on, hit the start engine switch and it makes a start sound that breaks up but does not idle or do anything past that. When I move the rudder control the horn plays dixe type horn which is weird because I downloaded a Kenworth horn.
All I really want it to do is door open close, start, idle, run with ESC, shutdown. Simple in my mind but cant get it to do it. And it seems that there should be more sounds available, I thought on the CD there were more sounds to choose from, unfortunately I didn't buy the CD this time.
Re: USM-RC-2 Think I may have waisted my money
Well, you once need the CD to get the according software.
Did you ever try the sound simulation in the ST? With it you can test all sound inputs you made for the several sound slots. Every single sound can also be tested directly in the according slot. Therefore it is quite impossible that you loaded horn X and hear horn Y. All available sounds can be tested directly at the PC out of the cd (without sound module).
Sounds on CD are in my opinion only examples an basics. Further lots of original sounds can be found int the web (e.g. youtube) an can be adapted to the module to get an individual sound set for a model. The manual and the available tutorials explain how to use the module and the sound editor to prepare new sounds for using with the module.
The USM-RC2 is NOT a plug-n-play soundboard, and in my eyes that is the greatest benefit of it! On delivery state it is 'naked', and all sound inputs and configurations CAN and MUST be made by the user himself.
Please take the module byside, use only the PC and the (newest) ST and generate your project with all the sounds and configurations you need. If there is al lack of sounds on the CD, complete it by downloading from the web and preparing with a sound editor (e.g. 'Audacity' from the CD). Then TEST the sonds ONLY with the 'sound simulation' function of the ST on your PC; of course using the PC sound card and speakers / earphones. ONLY when the simulation works well on your PC, than FIRST save the project on the PC hard disk (only SAVED projects are alterable!) and AT LAST store your project ONLY with the ST feature 'store project data to SD card' to your card. NEVER store files only with your PC on the SD card.
Before you do all this, PLEASE read the complete manual. It gives (nearly) all the hints and answers you need, and hundreds of users were successful in using it.
Did you ever try the sound simulation in the ST? With it you can test all sound inputs you made for the several sound slots. Every single sound can also be tested directly in the according slot. Therefore it is quite impossible that you loaded horn X and hear horn Y. All available sounds can be tested directly at the PC out of the cd (without sound module).
Sounds on CD are in my opinion only examples an basics. Further lots of original sounds can be found int the web (e.g. youtube) an can be adapted to the module to get an individual sound set for a model. The manual and the available tutorials explain how to use the module and the sound editor to prepare new sounds for using with the module.
The USM-RC2 is NOT a plug-n-play soundboard, and in my eyes that is the greatest benefit of it! On delivery state it is 'naked', and all sound inputs and configurations CAN and MUST be made by the user himself.
Please take the module byside, use only the PC and the (newest) ST and generate your project with all the sounds and configurations you need. If there is al lack of sounds on the CD, complete it by downloading from the web and preparing with a sound editor (e.g. 'Audacity' from the CD). Then TEST the sonds ONLY with the 'sound simulation' function of the ST on your PC; of course using the PC sound card and speakers / earphones. ONLY when the simulation works well on your PC, than FIRST save the project on the PC hard disk (only SAVED projects are alterable!) and AT LAST store your project ONLY with the ST feature 'store project data to SD card' to your card. NEVER store files only with your PC on the SD card.
Before you do all this, PLEASE read the complete manual. It gives (nearly) all the hints and answers you need, and hundreds of users were successful in using it.
Gruß
Gerhard
_________________
Panzermodelle 1:6
Gerhard
_________________
Panzermodelle 1:6
-
oberkaffeetante
- Beiträge: 26
- Registriert: Mi 4. Nov 2015, 08:09
- Wohnort: Magdeburg
- Kontaktdaten:
Re: USM-RC-2 Think I may have waisted my money
Hi kaf343,
first of all I think you will get used to use the USM-RC2 with time. As the module is not simple plug and play but highly configureable you should give you some to time to get to know each feature.
Maybe you can work step by step and test until you take the next feature in mind. So for example just connect the servo-cable that controlls the Motor to the Sound module and make the sounds for accelerating and breaking work. Here I would use sounds that came with the module, because these sounds have the right format and work fine with the module. In a next step you may add the sound for engine start/ stopp. If that works you may add more cables and configure more features, like light or so.
With that way of working you can see the influence of the changes you made.
After all the features work as desired you can start to replace the sounds with your own sounds
Best regards Uwe aka oberkaffeetante
first of all I think you will get used to use the USM-RC2 with time. As the module is not simple plug and play but highly configureable you should give you some to time to get to know each feature.
Maybe you can work step by step and test until you take the next feature in mind. So for example just connect the servo-cable that controlls the Motor to the Sound module and make the sounds for accelerating and breaking work. Here I would use sounds that came with the module, because these sounds have the right format and work fine with the module. In a next step you may add the sound for engine start/ stopp. If that works you may add more cables and configure more features, like light or so.
With that way of working you can see the influence of the changes you made.
After all the features work as desired you can start to replace the sounds with your own sounds
Best regards Uwe aka oberkaffeetante
Re: USM-RC-2 Think I may have waisted my money
Gentleman,
First let me thank you again for your help!
As I read more and play more I see that this is far from plug and play, and quite happy to see that. I bought this so I would have something different than the run of the mill.
I spent another few hours programming last night and was able to have a continuous sound simulation on my PC, WooHoo. And I was very happy for that, I then saved it again on my SD card and plugged it into my USM-RC-2, hooked up power, a receiver, ESC and servos. When I activated the switch to start the engine sound it made the cranking sound but never really ran more than about 10 seconds. As it was idling the sound was breaking in and out almost like a scratched record and never responded to the command from the radio to the ESC.
Am I getting close? Any thought would be greatly appreciated.
Also, what is the best way to switch the engine sound on and off, I would prefer to perform this task with the radio. Is it as simple as connecting the switch points on the card to an open channel on my receiver?
First let me thank you again for your help!
As I read more and play more I see that this is far from plug and play, and quite happy to see that. I bought this so I would have something different than the run of the mill.
I spent another few hours programming last night and was able to have a continuous sound simulation on my PC, WooHoo. And I was very happy for that, I then saved it again on my SD card and plugged it into my USM-RC-2, hooked up power, a receiver, ESC and servos. When I activated the switch to start the engine sound it made the cranking sound but never really ran more than about 10 seconds. As it was idling the sound was breaking in and out almost like a scratched record and never responded to the command from the radio to the ESC.
Am I getting close? Any thought would be greatly appreciated.
Also, what is the best way to switch the engine sound on and off, I would prefer to perform this task with the radio. Is it as simple as connecting the switch points on the card to an open channel on my receiver?
Re: USM-RC-2 Think I may have waisted my money
Well, when the sound (any sound!) goes quiet after a few seconds, it may be that the voltage of your battery is too low for your settings! Please check if you have chosen a "battery empty" voltage in your ST config which is not low enough to fit a nearly empty battery!
There are some ways to start / stop engine sound, see manual. I use an own switch channel combined with a beier switching module RC-SM-2, but you also may use the short moving of the gas channel to spare a seperate channel for starting / stopping.
There are some ways to start / stop engine sound, see manual. I use an own switch channel combined with a beier switching module RC-SM-2, but you also may use the short moving of the gas channel to spare a seperate channel for starting / stopping.
Gruß
Gerhard
_________________
Panzermodelle 1:6
Gerhard
_________________
Panzermodelle 1:6
Re: USM-RC-2 Think I may have waisted my money
Tell us the configuration in detail (see above) and upload the project file (*.usm), else it will be guesswork and waste everyones time.
Re: USM-RC-2 Think I may have waisted my money
I will upload the program as soon as I get home from work, thank you.
Re: USM-RC-2 Think I may have waisted my money
Hi,
Here is my program, seems to run fine on the PC but not when loaded into the sound card. It still breaks up and does not accelerate or have reverse.
Here is my program, seems to run fine on the PC but not when loaded into the sound card. It still breaks up and does not accelerate or have reverse.