servo mixing steering and tracks
servo mixing steering and tracks
Good day all.
I have a couple issues i need some help with.
I have the USM installed in a Famo half track.
I had the sound and steering/track mixing set up nicely, but for some reason after not using the model for about half a year it has corrupted.
The memory card cannot be read and the sterring/track mixing no longer works.
All sounds and lights still function ok.
I am a bit of a loss on how I set this up with cahnnel mixing on the USM so any pointers would be welcome.
I have Steering on servo 4
left track servo 3
Right track servo 5
I had the tx set up with the same assignments, driven from the left stick
Fwd/Rev 4
left 3
right 5
Any help would be much appreciated, I have lost all my notes that i created when it was built some years ago.
Alistair
I have a couple issues i need some help with.
I have the USM installed in a Famo half track.
I had the sound and steering/track mixing set up nicely, but for some reason after not using the model for about half a year it has corrupted.
The memory card cannot be read and the sterring/track mixing no longer works.
All sounds and lights still function ok.
I am a bit of a loss on how I set this up with cahnnel mixing on the USM so any pointers would be welcome.
I have Steering on servo 4
left track servo 3
Right track servo 5
I had the tx set up with the same assignments, driven from the left stick
Fwd/Rev 4
left 3
right 5
Any help would be much appreciated, I have lost all my notes that i created when it was built some years ago.
Alistair
Re: servo mixing steering and tracks
Hello Alistair,
some questions:
I assume that left and right track are controlled by an ESC, not a servo.
Also please confirm if "Steering" actually uses a servo for steering.
some questions:
What do you mean by servo 4, servo 3 etc., i.e. what do the numbers refer to?I have Steering on servo 4
left track servo 3
Right track servo 5
I assume that left and right track are controlled by an ESC, not a servo.
Also please confirm if "Steering" actually uses a servo for steering.
If it's the same assignment then how come 4 is fwd/rev here but above it's Steering?I had the tx set up with the same assignments, driven from the left stick
Fwd/Rev 4
left 3
right 5
Re: servo mixing steering and tracks
When all other sounds and light functions are still ok, it looks like more a issue in the TX!
The correct Mix needs to be created anyway on the TX side, in the USM-RC3 there are no mix options.
Which TX are you using? Is there a Vtail-Mix option (this is the Mix you need for your tracks)
If there is no Vtail-mix option, then this module can be a option:
https://www.mtroniks.net/prod/RC-Acces ... kmixer.htm
For a single engine setup, you need this:
V-Mix inputs are in your case TX channels 3 and 4 (Throttle and Ruder) and the outputs are Channels 5 and 6 (or via the TankMixer module) for your ESC´s.
For the USM you only need a single Prop#-1 input, coming from your TX Throttle stick (Channel 3 from your RX).
The correct Mix needs to be created anyway on the TX side, in the USM-RC3 there are no mix options.
Which TX are you using? Is there a Vtail-Mix option (this is the Mix you need for your tracks)
If there is no Vtail-mix option, then this module can be a option:
https://www.mtroniks.net/prod/RC-Acces ... kmixer.htm
For a single engine setup, you need this:
V-Mix inputs are in your case TX channels 3 and 4 (Throttle and Ruder) and the outputs are Channels 5 and 6 (or via the TankMixer module) for your ESC´s.
For the USM you only need a single Prop#-1 input, coming from your TX Throttle stick (Channel 3 from your RX).
Regards,
Marten
Marten
Re: servo mixing steering and tracks
Thanks for this let me look again at my note and try and clarify moreRascal hat geschrieben: ↑Mo 5. Okt 2026, 22:00 Hello Alistair,
some questions:
What do you mean by servo 4, servo 3 etc., i.e. what do the numbers refer to?I have Steering on servo 4
left track servo 3
Right track servo 5
I assume that left and right track are controlled by an ESC, not a servo.
Also please confirm if "Steering" actually uses a servo for steering.
If it's the same assignment then how come 4 is fwd/rev here but above it's Steering?I had the tx set up with the same assignments, driven from the left stick
Fwd/Rev 4
left 3
right 5
Re: servo mixing steering and tracks
The Mtroniks may be a good solution. I have a tiger 2 model and for that I programmed in the TX, but for some reaason the famo i plugged everything into the USM.MdG-77 hat geschrieben: ↑Mo 5. Okt 2026, 22:12 When all other sounds and light functions are still ok, it looks like more a issue in the TX!
The correct Mix needs to be created anyway on the TX side, in the USM-RC3 there are no mix options.
Which TX are you using? Is there a Vtail-Mix option (this is the Mix you need for your tracks)
If there is no Vtail-mix option, then this module can be a option:
For a single engine setup, you need this:
V-Mix inputs are in your case TX channels 3 and 4 (Throttle and Ruder) and the outputs are Channels 5 and 6 (or via the TankMixer module) for your ESC´s.
For the USM you only need a single Prop#-1 input, coming from your TX Throttle stick (Channel 3 from your RX).
Re: servo mixing steering and tracks
Well, the USM can’t create the correct Mix, so this needs to be done in your TX (or you need to use the Mtroniks)
When using the Mtroniks, you still need a separate channel, which is mixed with your Ruder channel-3 with a reduced output.
This Mix is needed to handle like a differential effect, so when your turn left, your Right track go’s a bit faster (bigger radius) and the Left track a bit slower.
(Or I get it wrong about the Famo setup, I just search for ‘Famo half track’ and see frontwheels and two tracks)
Or is there a auto mechanical differential in your model? (Without a servo)
If yes, then the Mix isn’t needed in both situations!
In this situation, you can use the 2 Servo outputs from the USM, with both a Direct Control from Prop#-1 (Throttle channel from TX)
Servo-1 is then your ESC for the Left Track and Servo-2 is the ESC for the Right Track.
When using the Mtroniks, you still need a separate channel, which is mixed with your Ruder channel-3 with a reduced output.
This Mix is needed to handle like a differential effect, so when your turn left, your Right track go’s a bit faster (bigger radius) and the Left track a bit slower.
(Or I get it wrong about the Famo setup, I just search for ‘Famo half track’ and see frontwheels and two tracks)
Or is there a auto mechanical differential in your model? (Without a servo)
If yes, then the Mix isn’t needed in both situations!
In this situation, you can use the 2 Servo outputs from the USM, with both a Direct Control from Prop#-1 (Throttle channel from TX)
Servo-1 is then your ESC for the Left Track and Servo-2 is the ESC for the Right Track.
Regards,
Marten
Marten
Re: servo mixing steering and tracks
Hello all,
for half track vehicles in bigger scales like the Famo 1/6 scale from Armortek there exist some specialized ESCs which combine double track motor steering with servo steering in the right way.
for half track vehicles in bigger scales like the Famo 1/6 scale from Armortek there exist some specialized ESCs which combine double track motor steering with servo steering in the right way.
Gruß
Gerhard
_________________
Panzermodelle 1:6
Gerhard
_________________
Panzermodelle 1:6
Re: servo mixing steering and tracks
Moin,
ich find, das Mischen sollte eigentlich im Sender passieren, wie MdG-77 schon gesagt hat. Naja, ich kenn mich mit dem USM nicht aus, aber bei Halbketten halt erst mal klären, ob da ein Differential drin ist oder nicht. Denn weiß man mal, ob man überhaupt einen Mischer braucht.
Gruß Klaus
ich find, das Mischen sollte eigentlich im Sender passieren, wie MdG-77 schon gesagt hat. Naja, ich kenn mich mit dem USM nicht aus, aber bei Halbketten halt erst mal klären, ob da ein Differential drin ist oder nicht. Denn weiß man mal, ob man überhaupt einen Mischer braucht.
Gruß Klaus
Re: servo mixing steering and tracks
Hallo,
das USM kann die eingehenden Signale nicht mischen und dann ausgeben, es kann nur die eingehenden Signale für den Fahrsound intern mischen wenn "2 Antriebsmotoren für Fahrsound" ausgewählt wurden und die (optionalen) Einstellungen "Mittelwert" und/oder "Lenkung auf Prop #2". Siehe Konfiguration > Fahrsound > Fahrsound.
das USM kann die eingehenden Signale nicht mischen und dann ausgeben, es kann nur die eingehenden Signale für den Fahrsound intern mischen wenn "2 Antriebsmotoren für Fahrsound" ausgewählt wurden und die (optionalen) Einstellungen "Mittelwert" und/oder "Lenkung auf Prop #2". Siehe Konfiguration > Fahrsound > Fahrsound.