Good day!
I would like to see up another function on a truck with an SFR1 that has already used both servo outputs. This would use a micro servo for operation.
I am using a FrSky Tandem X20 radio with a 10 channel RX. I do have a couple of the Beier 1210 ESCs I could use if needed to actuate the servo.
I'd also like the function to work along with a truck sound, say the horn and have the function remain in action the entire time the horn sounds. I am reasonably sure I could do this as one of the servo outputs, but was hoping for a way to do it without loosing existing functions.
Glad for any thoughts...thanks!
Third Servo Output on SFR1?
Re: Third Servo Output on SFR1?
Hello Matt,
the only option I see is to connect an Arduino or ESP32 to one of the servo outputs and then let the μP handle two (or even more) servos. I.e. the μP decodes the incoming signal from the transmitter, directly routed through the servo output, and depending on the impuls signal value controls servo A or servo B.
You didn't describe what the servos should do exactly and if you want to use direct control or just move to predefined positions but either should be possible with some clever coding.
Alternatively use a Multi-Funktion or Function-Sequence to trigger several functions simultaneously (e.g. play additional sound X, move servo Y to position Z etc.). Using a Function Sequence you can define for each function when it starts and how long it will remain active, and if the whole sequence should run once only or in a loop.
the only option I see is to connect an Arduino or ESP32 to one of the servo outputs and then let the μP handle two (or even more) servos. I.e. the μP decodes the incoming signal from the transmitter, directly routed through the servo output, and depending on the impuls signal value controls servo A or servo B.
You didn't describe what the servos should do exactly and if you want to use direct control or just move to predefined positions but either should be possible with some clever coding.
Not clear if this is only related to the additional servo or if you are asking in general, but there are the options "Sound at servo movement" and "Sound when not in home position" - the latter will play the sound as long as the servo is not in the pre-defined home position and it works with direct control and positions. Just put the desired sound into the sound slots "Sound from servo X left/right".I'd also like the function to work along with a truck sound, say the horn and have the function remain in action the entire time the horn sounds. I am reasonably sure I could do this as one of the servo outputs, but was hoping for a way to do it without loosing existing functions.
Alternatively use a Multi-Funktion or Function-Sequence to trigger several functions simultaneously (e.g. play additional sound X, move servo Y to position Z etc.). Using a Function Sequence you can define for each function when it starts and how long it will remain active, and if the whole sequence should run once only or in a loop.
Re: Third Servo Output on SFR1?
Thank you Rascal...helpful info. I will do some research on the Arduino or ESP32.
I am familiar with "sound at servo movement" as well as "sound when not home".
In this case, I am just looking for a servo to go from on position to another with sound.
Since posting, I may have found another option, too. Seems I have used one of the servo outputs for a woking steering wheel in the cab. I am thinking I can put a "Y" cable on ch1 and then re-use that servo output on the SFR1. I'll pull that truck apart and see if both servos turn the same way.
I am familiar with "sound at servo movement" as well as "sound when not home".
In this case, I am just looking for a servo to go from on position to another with sound.
Since posting, I may have found another option, too. Seems I have used one of the servo outputs for a woking steering wheel in the cab. I am thinking I can put a "Y" cable on ch1 and then re-use that servo output on the SFR1. I'll pull that truck apart and see if both servos turn the same way.
Re: Third Servo Output on SFR1?
An Update...I was using one of the Servo outputs to have a servo controlled steering wheel in the cab, turn with the truck's steering. When connected via a splitter on the RX - it was turning in the wrong direction. A servo reverse cable has remedied this.
So, I have an open servo output on the SFR1. Currently, I use SBUS #3, where "up" on the stick plays one horn sound effect....and down plays a different horn sound effect. On the latter, the horn plays as long as the stick is held down.
Is it possible to have the servo output only work on the "down" side of the movement with the SFX...and just the "up"direction play an SFX only?
Or should I take an unused prop channel for the servo control triggered/fed by the same radio channel as the horn sound?
So, I have an open servo output on the SFR1. Currently, I use SBUS #3, where "up" on the stick plays one horn sound effect....and down plays a different horn sound effect. On the latter, the horn plays as long as the stick is held down.
Is it possible to have the servo output only work on the "down" side of the movement with the SFX...and just the "up"direction play an SFX only?
Or should I take an unused prop channel for the servo control triggered/fed by the same radio channel as the horn sound?
Re: Third Servo Output on SFR1?
Hello Matt,
Multi function X
Label: Servo+Sound
Function 1: "Additional sound X"
Function 2: "Servo X Position 1"
Function 3: "-"
Make sure that "Automatic return to home position ..." is ticked for servo X so that it returns to its original position once the stick goes back to neutral.
As mentioned above you can use a Multi function to play a sound and move the servo to a pre-defined position at the same time. Just replace the function "Additional sound X" on the down side with "Multi function X" which is configured as follows:Is it possible to have the servo output only work on the "down" side of the movement with the SFX...and just the "up"direction play an SFX only?
Multi function X
Label: Servo+Sound
Function 1: "Additional sound X"
Function 2: "Servo X Position 1"
Function 3: "-"
Make sure that "Automatic return to home position ..." is ticked for servo X so that it returns to its original position once the stick goes back to neutral.
Also possible.Or should I take an unused prop channel for the servo control triggered/fed by the same radio channel as the horn sound?
Re: Third Servo Output on SFR1?
Thanks Rascal...I'll play with those options. I misunderstood the multi-function option. Always thankful for your expertise.