EMS 16G did not work well with Graupner FM4014

NMS-, EMS- MSC- und SMS-Module
Antworten
Pelican32
Beiträge: 3
Registriert: So 25. Jan 2026, 09:35

EMS 16G did not work well with Graupner FM4014

Beitrag von Pelican32 »

I recently bought EMS 16G to install in the left empty slow of my Graupner FM4014 with an existing 4108 Nautic module in the right slow of the transmitter
When I checked the voltage at the output of the Nautic 4149 receiver module I found :

When the switches of the EMS are up :

+6volts on red/black wires
+6V on orange/black
0V on red/orange

When the switches are down : O Volts on all wires !!

I expected + 6Volts on red/orange ( with is the case using the Graupner 4108 Nautic module with 4149 receiver module.

Any idea about this issue ?

Thank you[*]
Benutzeravatar
BEIER-Electronic Andy
Administrator
Beiträge: 4557
Registriert: Mi 17. Dez 2008, 07:37

Re: EMS 16G did not work well with Graupner FM4014

Beitrag von BEIER-Electronic Andy »

Hello,

I'm afraid I don't understand exactly where you measured these voltages.

Graupner no. 4149 appears to be a Y-cable? Do you mean part number 4159?

What kind of module do you want to control with the EMS-16-G?
Pelican32
Beiträge: 3
Registriert: So 25. Jan 2026, 09:35

Re: EMS 16G did not work well with Graupner FM4014

Beitrag von Pelican32 »

Thank for your Quick answer.
The configuration is as follow:
FM4014 top right slot Graupner 4108 connected on slot 6 inside the 4014 trasmitter
FM4014 top left slot EMS 16 G connected on slot 7 inside the transmitter using the 3 wires câble
I used 2-16K Graupner 4159 as a Nautic decoder throught of course a. FM receiver
On the 4159 Graupner module I powered it with 6V NiMh battery
I plugged Graupner relay module 3754/2 ( single 3 wires câble) on each output of the Graupner 4159 décoder.
When I switched up EMS 16G it is OK ( 1 relay of the 3754 is workng fine) but when I switched down nothing happened.
This behavior is not the same with 4108 module : when I switched down the second relay is running.
I did the same test without relay module connected on the décoder and I measure the voltage on the 3 pins connectors (x8) of the décoder and the results are what I described on my first post.
Benutzeravatar
BEIER-Electronic Andy
Administrator
Beiträge: 4557
Registriert: Mi 17. Dez 2008, 07:37

Re: EMS 16G did not work well with Graupner FM4014

Beitrag von BEIER-Electronic Andy »

I was afraid of that. You can't control a Graupner decoder with the EMG-16-G.

The EMS-16-G uses a completely different protocol and can only control our following modules:
  • Sound speed controller SFR-1, SFR-1-D and SFR-1-HL
  • Sound module USM-RC-2, USM-RC-3 and USM-HL-2
  • Speed controller UFR-1230 and UFR-1230-D
  • Switching module RC-SM-16
Pelican32
Beiträge: 3
Registriert: So 25. Jan 2026, 09:35

Re: EMS 16G did not work well with Graupner FM4014

Beitrag von Pelican32 »

OK understood !. Many thanks

Is there a notice to use the RC SM 16module with FM4014 ? Wiring , warning, compatibility with the existing 4108 already used ?
Does it means the RC SM16 should be plugged on slot 7 of the FM receiver ( if I m using slot 7 inside the FM4014 for the EMS 16.

Regards
Benutzeravatar
BEIER-Electronic Andy
Administrator
Beiträge: 4557
Registriert: Mi 17. Dez 2008, 07:37

Re: EMS 16G did not work well with Graupner FM4014

Beitrag von BEIER-Electronic Andy »

We are not aware of any problems with that.

Yes, the RC-SM-16 is then plugged into slot 7 of the receiver.
Antworten