2 functions, 1 switch

Soundmodul und Fahrtregler in einem Modul
Antworten
Sev
Beiträge: 8
Registriert: Do 11. Jul 2024, 21:20

2 functions, 1 switch

Beitrag von Sev »

Hey all,

I have missed something with my idea, and hope you smart folks can help me out. Beier SFR-1 in the truck, Beier LM-BT-16 module in the trailer. Trailer has the Tamiya Motorized Legs which I have already implemented into the LM. 5th wheel coupler on the truck is also servo operated, plugged into Servo Output 1 on the SFR, and have it activated in the Sound Teacher

I have two function sequences setup to run the coupler open/close and motor up/down. As follows.

Function Sequence 1
Servo 1 Posistion 1: On (opens coupler)
LM Motor Down: On (3.50 seconds on duration)
LM Motor Down: Off

Function Sequence 2
Servo 1 Posistion 2: On (closes coupler)
LM Motor Up: On (3.50 seconds on duration)
LM Motor Up: Off

I have these set to my 2 pos. switch as follows:
In Static A: Function Sequence 1
In Static D: Function sequence 2

The legs work as they should, going up or down with the switch, and the motor shuts off as it should. The servo for the coupler does nothing. Endpoints are set in the transmitter. I've been banging my head against it, and cannot get the coupler to work with the function sequences. Any input or ideas is appreciated!
Rascal
Beiträge: 4113
Registriert: Do 9. Okt 2014, 01:31

Re: 2 functions, 1 switch

Beitrag von Rascal »

Hello Sev,

please upload the project file (*.sfr) for me to check.

The 2 position switch is +100% / -100% ?
Is the switch latching or momentary?
Sev
Beiträge: 8
Registriert: Do 11. Jul 2024, 21:20

Re: 2 functions, 1 switch

Beitrag von Sev »

Thanks for the reply Rascal. Those terms are foreign to me as far as latching/momentary. The transmitter is a FlySky ST8 if that helps.

Sure! I'll upload it when I get home from work. You might be asleep by then since I'm in California.
Rascal
Beiträge: 4113
Registriert: Do 9. Okt 2014, 01:31

Re: 2 functions, 1 switch

Beitrag von Rascal »

Hello,

latching: the switch will stay in its "ON" position after pushed, even you don't touch it anymore
momentary: the switch will only stay in the "ON" position as long as you push it / hold it there
Sev
Beiträge: 8
Registriert: Do 11. Jul 2024, 21:20

Re: 2 functions, 1 switch

Beitrag von Sev »

Ahh ok, Thank you! It's a latching switch then.

Here's the requested project file.
Dateianhänge
Knight Hauler 2.sfr
SFR project file
(39.41 KiB) 128-mal heruntergeladen
Rascal
Beiträge: 4113
Registriert: Do 9. Okt 2014, 01:31

Re: 2 functions, 1 switch

Beitrag von Rascal »

Hello Sev,

you didn't configure any of the servo positions, they are all still set to 1,500ms (default).

servos.png
servos.png (69.13 KiB) 2979 mal betrachtet
Sev
Beiträge: 8
Registriert: Do 11. Jul 2024, 21:20

Re: 2 functions, 1 switch

Beitrag von Sev »

Gotcha. So these override the end points in the transmitter? Thank you for your time taking a look, I'll get these set after work.
Rascal
Beiträge: 4113
Registriert: Do 9. Okt 2014, 01:31

Re: 2 functions, 1 switch

Beitrag von Rascal »

Sev hat geschrieben: ↑Fr 12. Jul 2024, 14:12Gotcha. So these override the end points in the transmitter? Thank you for your time taking a look, I'll get these set after work.
This is not related to the transmitter since you use a function ("Servo X Position #") to control the servos, as opposed to direct control.
Those values therefore set the absolute position of the servo but note that different servos have a different maximum angle, so the value will depend on the actual servo used (hence why we can't express the value in degrees).

You need to figure out the correct values for your servo, in one position the 5th wheel is open and on the other it's closed but without the servo hitting a mechanical stop at either end. If it does the servo will usually hum/buzz and draw a high current, so that should be avoided.

If you have a servo tester with display you can use that to determine the values. Starting at 1500 µs (= 1,500 ms) use the tester to move the servo into the correct positions (coupler open & closed) and set the value on the display as servo position.

If you do not have a servo tester change the position in small steps and try, i.e. starting with 1,400 ms for Position #1 and 1,600 ms for Position #2.
Then decrease/increase the values in small steps until the coupler is fully open or fully closed respectively.
Sev
Beiträge: 8
Registriert: Do 11. Jul 2024, 21:20

Re: 2 functions, 1 switch

Beitrag von Sev »

Ok, that makes a lot of sense now. I do have a servo tester, but it's just a basic one with a knob and centering function, no display. I'll implement the second method and hopefully get those posistons correct. Thank you so much for the help!
Sev
Beiträge: 8
Registriert: Do 11. Jul 2024, 21:20

Re: 2 functions, 1 switch

Beitrag von Sev »

*UPDATE* - It works! Thanks to Rascal for pointing out my mistake and suggesting I order a better servo tester with display. I did have to change step one of Function Sequnce 1 to "Servo at home posistion" with the settings from the tester (don't know why servo 1pos 1 didn't work). Both functions are now operating off 1 switch as they should. Thank you again Rascal for your help and imput!
Antworten