Auto Cancel Indicators
Auto Cancel Indicators
Good day!
In my trucks, I have a three way switch for the turn signals. One way is left - center is off - other way is right. They are not set to automatically work when the steering is turned.
In one truck, they automatically turn off after a turn is executed. For example, I'll put on the left indicator...after the truck makes the turn...the indicator stops flashing even though the switch is still set to the "left" position.
Despite having the same settings in another truck...it does not automatically cancel after the turn. The indicator remains flashing.
Glad for thoughts on how to correct.
In my trucks, I have a three way switch for the turn signals. One way is left - center is off - other way is right. They are not set to automatically work when the steering is turned.
In one truck, they automatically turn off after a turn is executed. For example, I'll put on the left indicator...after the truck makes the turn...the indicator stops flashing even though the switch is still set to the "left" position.
Despite having the same settings in another truck...it does not automatically cancel after the turn. The indicator remains flashing.
Glad for thoughts on how to correct.
Re: Auto Cancel Indicators
Hello Matt,
have you enabled the option "Switch off indicator after X flashes" under Configuration > Outputs > Output options ?
I recommend to use a momentary switch with memory to switch on the indicators. Alternatively enable memory and operate the latching switch like a momentary switch, i.e. return the switch immediately to the middle position after the indicator has been turned on.
have you enabled the option "Switch off indicator after X flashes" under Configuration > Outputs > Output options ?
I recommend to use a momentary switch with memory to switch on the indicators. Alternatively enable memory and operate the latching switch like a momentary switch, i.e. return the switch immediately to the middle position after the indicator has been turned on.
Re: Auto Cancel Indicators
Hi Rascal...Rascal hat geschrieben: ↑So 9. Jun 2024, 11:25 Hello Matt,
have you enabled the option "Switch off indicator after X flashes" under Configuration > Outputs > Output options ?
I recommend to use a momentary switch with memory to switch on the indicators. Alternatively enable memory and operate the latching switch like a momentary switch, i.e. return the switch immediately to the middle position after the indicator has been turned on.
I don't believe I have "Switch off indicator after X flashes" selected...but will check. The radio doesn't have a monetary switch but I can also look into "enable memory".
It's a bit strange as I don't see any difference in the settings between the truck that does work that way...and the ones that don't.
Re: Auto Cancel Indicators
Quick thought: Are all of your trucks on the same software version?
Maybe in one version it works when in another one it doesn't - question then would be what the intended behaviour should be.
Maybe in one version it works when in another one it doesn't - question then would be what the intended behaviour should be.
Grüße,
Stefan
Diverse RC-Cars (On- & Offroad), Trucks im Tamiya-Maßstab
Stefan
Diverse RC-Cars (On- & Offroad), Trucks im Tamiya-Maßstab
Re: Auto Cancel Indicators
Sorry for the delay....I do believe I am using the same software version.
I just looked at this again tonight....and I have the settings for this matched to the first truck I built. Yet, in the other two....the indicators don't self-cancel
I will say that besides the 3 way switch, I have the radio's gyro set so that if I tilt the TX to the left....the left indicator works as long as I keep it tilted. Same thing to the right.
Perhaps I should just forget it and use the tilt method as opposed to the switch. This would also free up the switch for something else.
I just looked at this again tonight....and I have the settings for this matched to the first truck I built. Yet, in the other two....the indicators don't self-cancel
I will say that besides the 3 way switch, I have the radio's gyro set so that if I tilt the TX to the left....the left indicator works as long as I keep it tilted. Same thing to the right.
Perhaps I should just forget it and use the tilt method as opposed to the switch. This would also free up the switch for something else.
- BEIER-Electronic Andy
- Administrator
- Beiträge: 4557
- Registriert: Mi 17. Dez 2008, 07:37
Re: Auto Cancel Indicators
The indicators are always switched off via the steering (just like in a real car).
If this doesn't work for you with some modules, then the direction of the steering signal is probably reversed. This means you can steer correctly, but internally the SFR-1 thinks you have steered in the other direction and does not switch off the indicator. You can also test this by, for example, blinking right with such a module and then steering left. Then the indicator should also go off there.
You can set the direction of the steering signal in the sound teacher. If you want, you can also intentionally set it incorrectly to prevent the indicators from automatically switching off.
If this doesn't work for you with some modules, then the direction of the steering signal is probably reversed. This means you can steer correctly, but internally the SFR-1 thinks you have steered in the other direction and does not switch off the indicator. You can also test this by, for example, blinking right with such a module and then steering left. Then the indicator should also go off there.
You can set the direction of the steering signal in the sound teacher. If you want, you can also intentionally set it incorrectly to prevent the indicators from automatically switching off.
- Dateianhänge
-
- SFR-1_Lenkkanal-Invertierung.png (13.91 KiB) 3653 mal betrachtet
Re: Auto Cancel Indicators
Sorry for the delay , Andy.
You may have led me to the answer! On the first truck, I believe I am using the steering X2/2. I didn't have room for that on the rollback, so I plugged the steering directly into the receiver.
I assume I must use the steering X2/2 for the auto cancelling indicators? I can certainly do that on this new truck.
You may have led me to the answer! On the first truck, I believe I am using the steering X2/2. I didn't have room for that on the rollback, so I plugged the steering directly into the receiver.
I assume I must use the steering X2/2 for the auto cancelling indicators? I can certainly do that on this new truck.
Re: Auto Cancel Indicators
You must use Prop #2 for steering, either via X2/2 plugged into the receiver or via SBUS channel.
If the servo must remain connected to the receiver use a Y-cable in case of the first option.
Re: Auto Cancel Indicators
I didn't use the X2/2 in the rollback....as it's a day cab and there was so much to fit...that I just wasn't able to use those cables. I just used the SBUS.
I assume without the X2/2 connected, I cannot get the auto cancel feature on this truck.
Hooking up with the X2/2 on this new truck has return the auto cancel feature.
I assume without the X2/2 connected, I cannot get the auto cancel feature on this truck.
Hooking up with the X2/2 on this new truck has return the auto cancel feature.
Re: Auto Cancel Indicators
You don't need to use X2/2.
Auto cancel works via Prop #2 as long as it is configured as steering channel, see Configuration > General > Module configuration > "Steering with prop. channel #2".I assume without the X2/2 connected, I cannot get the auto cancel feature on this truck.
It does not matter if Prop #2 gets it signal via X2/2 or some SBUS channel.