Sfr 1 possibly damaged after taking sd card out still powered on

Soundmodul und Fahrtregler in einem Modul
Antworten
Eivinboy
Beiträge: 8
Registriert: So 22. Mai 2022, 01:40

Sfr 1 possibly damaged after taking sd card out still powered on

Beitrag von Eivinboy »

So a few days ago i got my new sfr 1 for my truck and ive been working on it but it apears ive maybe smoked or burnt out a part of it. As seen in the attachment below there apears to be a round burn mark or whatever on one of the chips. So what i did cause i was programming it so much i just took out the sd card when it was all powered up because turning it on and off was a bit anoyying and ive removed the sd card from my usm rc 2 before without turning it off and nothing bad happend. But this time when i removed the sd card it just made a big pop sound so i took out the battery as quickly as i could. At first i thought it was my motor because there were som cables that were possibly touching but now with a new motor i still cant get it to work. It gives the green static led when powered on but the second i try and initiate the motor it starts blinking red. Not sure what to do but doesnt look like my motor was the only thing damaged.
Dateianhänge
InkedIMG_4456_LI.jpg
InkedIMG_4456_LI.jpg (160.57 KiB) 2356 mal betrachtet
Rascal
Beiträge: 4113
Registriert: Do 9. Okt 2014, 01:31

Re: Sfr 1 possibly damaged after taking sd card out still powered on

Beitrag von Rascal »

Hello,
Eivinboy hat geschrieben: ↑Sa 4. Jun 2022, 16:34 So a few days ago i got my new sfr 1 for my truck and ive been working on it but it apears ive maybe smoked or burnt out a part of it. As seen in the attachment below there apears to be a round burn mark or whatever on one of the chips.
That's chip is a voltage regulator. If that's fried the SFR-1 will not work anymore (but see below first).
So what i did cause i was programming it so much i just took out the sd card when it was all powered up because turning it on and off was a bit anoyying and ive removed the sd card from my usm rc 2 before without turning it off and nothing bad happend.
Not a good idea, in both manuals it says that the module should be powered off when inserting or ejecting the SD card!
But this time when i removed the sd card it just made a big pop sound so i took out the battery as quickly as i could. At first i thought it was my motor because there were som cables that were possibly touching but now with a new motor i still cant get it to work. It gives the green static led when powered on but the second i try and initiate the motor it starts blinking red.
Does it blink slowly or fast? In any case it indicates a problem with the SD card. Try another SD card first to see if that's causing the problem.
Not sure what to do but doesnt look like my motor was the only thing damaged.
I doubt that the handling of the SD card would damage the motor. Have you tried running the motor directly from the battery to see if it still works or not?
If the SFR-1 is damaged then of course neither the old nor new motor will work, but that doesn't mean the old motor is damaged.
Eivinboy
Beiträge: 8
Registriert: So 22. Mai 2022, 01:40

Re: Sfr 1 possibly damaged after taking sd card out still powered on

Beitrag von Eivinboy »

Rascal hat geschrieben: ↑Sa 4. Jun 2022, 19:58 Hello,
Eivinboy hat geschrieben: ↑Sa 4. Jun 2022, 16:34 So a few days ago i got my new sfr 1 for my truck and ive been working on it but it apears ive maybe smoked or burnt out a part of it. As seen in the attachment below there apears to be a round burn mark or whatever on one of the chips.
That's chip is a voltage regulator. If that's fried the SFR-1 will not work anymore (but see below first).
So what i did cause i was programming it so much i just took out the sd card when it was all powered up because turning it on and off was a bit anoyying and ive removed the sd card from my usm rc 2 before without turning it off and nothing bad happend.
Not a good idea, in both manuals it says that the module should be powered off when inserting or ejecting the SD card!
But this time when i removed the sd card it just made a big pop sound so i took out the battery as quickly as i could. At first i thought it was my motor because there were som cables that were possibly touching but now with a new motor i still cant get it to work. It gives the green static led when powered on but the second i try and initiate the motor it starts blinking red.
Does it blink slowly or fast? In any case it indicates a problem with the SD card. Try another SD card first to see if that's causing the problem.
Not sure what to do but doesnt look like my motor was the only thing damaged.
I doubt that the handling of the SD card would damage the motor. Have you tried running the motor directly from the battery to see if it still works or not?
If the SFR-1 is damaged then of course neither the old nor new motor will work, but that doesn't mean the old motor is damaged.
It blinks red quickly and no ive not tried running the motor on just a battery.
Eivinboy
Beiträge: 8
Registriert: So 22. Mai 2022, 01:40

Re: Sfr 1 possibly damaged after taking sd card out still powered on

Beitrag von Eivinboy »

Rascal hat geschrieben: ↑Sa 4. Jun 2022, 19:58 Hello,
Eivinboy hat geschrieben: ↑Sa 4. Jun 2022, 16:34 So a few days ago i got my new sfr 1 for my truck and ive been working on it but it apears ive maybe smoked or burnt out a part of it. As seen in the attachment below there apears to be a round burn mark or whatever on one of the chips.
That's chip is a voltage regulator. If that's fried the SFR-1 will not work anymore (but see below first).
So what i did cause i was programming it so much i just took out the sd card when it was all powered up because turning it on and off was a bit anoyying and ive removed the sd card from my usm rc 2 before without turning it off and nothing bad happend.
Not a good idea, in both manuals it says that the module should be powered off when inserting or ejecting the SD card!
But this time when i removed the sd card it just made a big pop sound so i took out the battery as quickly as i could. At first i thought it was my motor because there were som cables that were possibly touching but now with a new motor i still cant get it to work. It gives the green static led when powered on but the second i try and initiate the motor it starts blinking red.
Does it blink slowly or fast? In any case it indicates a problem with the SD card. Try another SD card first to see if that's causing the problem.
Not sure what to do but doesnt look like my motor was the only thing damaged.
I doubt that the handling of the SD card would damage the motor. Have you tried running the motor directly from the battery to see if it still works or not?
If the SFR-1 is damaged then of course neither the old nor new motor will work, but that doesn't mean the old motor is damaged.
Went ahead and used a multimeter on the new motor and the highest voltage i got was 0.10 volts so i guess i have a bad connection or something.
Eivinboy
Beiträge: 8
Registriert: So 22. Mai 2022, 01:40

Re: Sfr 1 possibly damaged after taking sd card out still powered on

Beitrag von Eivinboy »

Rascal hat geschrieben: ↑Sa 4. Jun 2022, 19:58 Hello,
Eivinboy hat geschrieben: ↑Sa 4. Jun 2022, 16:34 So a few days ago i got my new sfr 1 for my truck and ive been working on it but it apears ive maybe smoked or burnt out a part of it. As seen in the attachment below there apears to be a round burn mark or whatever on one of the chips.
That's chip is a voltage regulator. If that's fried the SFR-1 will not work anymore (but see below first).
So what i did cause i was programming it so much i just took out the sd card when it was all powered up because turning it on and off was a bit anoyying and ive removed the sd card from my usm rc 2 before without turning it off and nothing bad happend.
Not a good idea, in both manuals it says that the module should be powered off when inserting or ejecting the SD card!
But this time when i removed the sd card it just made a big pop sound so i took out the battery as quickly as i could. At first i thought it was my motor because there were som cables that were possibly touching but now with a new motor i still cant get it to work. It gives the green static led when powered on but the second i try and initiate the motor it starts blinking red.
Does it blink slowly or fast? In any case it indicates a problem with the SD card. Try another SD card first to see if that's causing the problem.
Not sure what to do but doesnt look like my motor was the only thing damaged.
I doubt that the handling of the SD card would damage the motor. Have you tried running the motor directly from the battery to see if it still works or not?
If the SFR-1 is damaged then of course neither the old nor new motor will work, but that doesn't mean the old motor is damaged.
So ive now tried to connect the old motor to a battery and it works just fine. So question now is what may be causing the lack of power to the motor? Ive checked voltage on the motor itself and from the module but there just isnt any power coming from the module to the motor.
Rascal
Beiträge: 4113
Registriert: Do 9. Okt 2014, 01:31

Re: Sfr 1 possibly damaged after taking sd card out still powered on

Beitrag von Rascal »

Hello,

have you tried replacing the SD card? If yes, what's the status of the LEDs now?
Eivinboy
Beiträge: 8
Registriert: So 22. Mai 2022, 01:40

Re: Sfr 1 possibly damaged after taking sd card out still powered on

Beitrag von Eivinboy »

Rascal hat geschrieben: ↑Mo 6. Jun 2022, 15:30 Hello,

have you tried replacing the SD card? If yes, what's the status of the LEDs now?
Yeah replaced it with the old sd card i used in my usm rc 2 but still nothing. When powered on its solid green any nothing else but when i try to Drive forward/backward it then starts fast blinking red until it shut off still with a solid green.
Benutzeravatar
BEIER-Electronic Andy
Administrator
Beiträge: 4557
Registriert: Mi 17. Dez 2008, 07:37

Re: Sfr 1 possibly damaged after taking sd card out still powered on

Beitrag von BEIER-Electronic Andy »

It looks as if the motor output stage has a defect.

Please send the module (with SD card) for inspection / repair to our address (or to the shop where you bought the SFR-1):
BEIER-Electronic
Winterbacher Str. 52/4
73614 Schorndorf
Germany

I don't know where you live, but if it's not in the EU, then please state on the customs documents for the return that it is a defective module and state a low value (10 EUR).
Antworten