Volume Control (remotely)

Soundmodul für Fahrgeräusche (speziell für RC-Modelle). Der Nachfolger des USM-RC
Antworten
tizdaz
Beiträge: 36
Registriert: Mi 22. Jul 2020, 04:09

Volume Control (remotely)

Beitrag von tizdaz »

Remotely control volume?

Hi guys, ive tried but cant figure it out,

How do i set this up so i can remotely control the volume via my TX?

My TX is this: https://www.flysky-cn.com/fsi6s

it has 2 self centering knobs so i would like to use one of these for volume control, but not sure how?

Thanks
Rascal
Beiträge: 4113
Registriert: Do 9. Okt 2014, 01:31

Re: Volume Control (remotely)

Beitrag von Rascal »

Hi,

if the knobs are self-centering then you can't use those for "Direct volume control" (proportional volume control); whenever the knob centers it will also change back the volume according to that center position. You could use the knob as a momentary switch though:

First assign the knob to a channel on the transmitter (for 'how to' refer to the transmitter's manual) with 100% servo travel to the left and right. Then use a servo connected to that receiver channel and test if it moves left or right when the knob is turned.

If that works ok disconnect the servo and connect the receiver-channel to a prop channel (#2 to #4) using a patch cable.

Now assign the functions "Volume +" and "Volume -" to the selected prop channel. Whenever you briefly turn the knob fully to the left or right (until it hits the stop) the volume should be increased or decreased by one step.

That being said I see that you have already assigned functions to Prop #2 to #4, perhaps it would be easier to replace two of them with "Volume +" and "Volume -" in the column "In position (static)". Use a momentary 3-way switch preferrably.
tizdaz
Beiträge: 36
Registriert: Mi 22. Jul 2020, 04:09

Re: Volume Control (remotely)

Beitrag von tizdaz »

Hi Rascal,

Thanks for quick reply :)

Ive done a mod that allows me to remove the spring from the knob so it now stays in whatever position i put it in :)

I will follow your instructions & report back,

Thanks again!
tizdaz
Beiträge: 36
Registriert: Mi 22. Jul 2020, 04:09

Re: Volume Control (remotely)

Beitrag von tizdaz »

Rascal hat geschrieben: ↑Fr 22. Okt 2021, 23:11
Now assign the functions "Volume +" and "Volume -" to the selected prop channel. Whenever you briefly turn the knob fully to the left or right (until it hits the stop) the volume should be increased or decreased by one step.
im confused!

ive assigned the prop channel on my TX to channel 5 on my RX, ive tested it with a servo & servo moves when i turn the knob.

But i dont know what column in the software i have to add these voulme functions!?
Screenshot 2021-10-23 004650.png
Screenshot 2021-10-23 004650.png (14.71 KiB) 2967 mal betrachtet
Rascal
Beiträge: 4113
Registriert: Do 9. Okt 2014, 01:31

Re: Volume Control (remotely)

Beitrag von Rascal »

Hi,

if you use the knob as momentary switch I recommend to put the functions in column "In position (static)" area A (Volume+) and D (Volume-) since it would be difficult to repeatedly hit area B and C, considering that you need to turn the knob a few times before changes in volume become audible.
(With a light function for example it's easier to use B and C as you only need one turn and you can see if the light is on or off.)

But since you have removed the spring I think what you actually want is proportional volume control, just go to Configuration > General > Volume and assign Prop #2 to "Direct volume control:". Note that Prop #2 can then not be used for other functions anymore.
tizdaz
Beiträge: 36
Registriert: Mi 22. Jul 2020, 04:09

Re: Volume Control (remotely)

Beitrag von tizdaz »

hi there,

ok i have a new TX (Futaba T6K) which has a rotary knob on it:
https://www.nexusmodels.co.uk/futaba-t6 ... ode-2.html

I've managed to set it up so i can now control the volume remotely, but how do i set it up to work like a normal rotary volume control so when i turn it to a particular position then the volume stays at that level, because at the moment i have to keep putting the rotary knob back to the centre?


Thanks!
Rascal
Beiträge: 4113
Registriert: Do 9. Okt 2014, 01:31

Re: Volume Control (remotely)

Beitrag von Rascal »

Hello,
tizdaz hat geschrieben: ↑Sa 30. Okt 2021, 17:41 I've managed to set it up so i can now control the volume remotely, but how do i set it up to work like a normal rotary volume control so when i turn it to a particular position then the volume stays at that level, because at the moment i have to keep putting the rotary knob back to the centre?
I quote myself:
But since you have removed the spring I think what you actually want is proportional volume control, just go to Configuration > General > Volume and assign Prop #2 to "Direct volume control:". Note that Prop #2 can then not be used for other functions anymore.
Antworten