how to connect Vantage Lightbar

Soundmodul für Fahrgeräusche (speziell für RC-Modelle). Der Nachfolger des USM-RC
Jimmy777
Beiträge: 18
Registriert: So 11. Mär 2018, 09:50

Re: how to connect Vantage Lightbar

Beitrag von Jimmy777 »

Sorry, I missed that part.

Output 5 is yellow
Output 8 is black
Rascal
Beiträge: 4113
Registriert: Do 9. Okt 2014, 01:31

Re: how to connect Vantage Lightbar

Beitrag von Rascal »

Ok. But I see that neither output 5 nor 8 is configured in "Outputs". They should both be configured as "Static (Sound Prop)".

Under proportional channels Prop #3 you have configured Output 8 and "Engine sound on/off" in position D - that could be a bit tricky because if you hold the stick too long in that position the engine sound may switch on or off when you actually try to change the pattern of the light bar (which then may or may not change).
At least for testing you should put one function only in one area, this way it will be less confusing if something else "happens". Makes troubleshooting a lot easier and later when everthing works you can still configure it as desired.

Anway, configure the outputs first and let us know if that solved the problem.
Jimmy777
Beiträge: 18
Registriert: So 11. Mär 2018, 09:50

Re: how to connect Vantage Lightbar

Beitrag von Jimmy777 »

Yes I missed that one. I programmed them at first but must have changed something without saving. Its now changed and I also changed the start engine position.

But It´s still the same. I move the stick in long position. It goes on. I move the stick in oppostie I change the pattern but it´s still only the two I had before.
Dateianhänge
test2.usm
(38.75 KiB) 245-mal heruntergeladen
Rascal
Beiträge: 4113
Registriert: Do 9. Okt 2014, 01:31

Re: how to connect Vantage Lightbar

Beitrag von Rascal »

Configuration looks ok now. Try this:

1. Disconnect the yellow cable from output 5.
2. Switch on the lightbar via the transmitter.
3. Now briefly touch minus (X1/2).
4. Wait a second or two.

Repeat 3. to 4. a few times.

Does the pattern change every time you touch minus?
Jimmy777
Beiträge: 18
Registriert: So 11. Mär 2018, 09:50

Re: how to connect Vantage Lightbar

Beitrag von Jimmy777 »

Yes the pattern changes every time i put the yellow cable to X1 but it´s still only the same two patterns as before.
After 2 times it starts over again with the pattern.
Rascal
Beiträge: 4113
Registriert: Do 9. Okt 2014, 01:31

Re: how to connect Vantage Lightbar

Beitrag von Rascal »

In this case I would contact the manufacturer of the light bar and see what they say.
Jimmy777
Beiträge: 18
Registriert: So 11. Mär 2018, 09:50

Re: how to connect Vantage Lightbar

Beitrag von Jimmy777 »

Ok, I will do that. Thanks you so much for all the help so far. :D :D :D
Jimmy777
Beiträge: 18
Registriert: So 11. Mär 2018, 09:50

Re: how to connect Vantage Lightbar

Beitrag von Jimmy777 »

Finally I got the light bar back and it was broken. I got a new one and now I tried connect and the pattern change.

But....

I have connected the yellow cable to output 5 and black on 8. I can start and stop the lightbar without any problems many times.

But when I try change pattern the light stops and just glows. sometimes its a few and sometimes its all lights on the lightbar.
If I disconnect the yellow cable it starts blinking again and every time i touch output 5 with yellow cable the pattern change but as long as it´s connected it´s not working. What did I miss???
Dateianhänge
test2.usm
(38.61 KiB) 222-mal heruntergeladen
Rascal
Beiträge: 4113
Registriert: Do 9. Okt 2014, 01:31

Re: how to connect Vantage Lightbar

Beitrag von Rascal »

Since output 5 is configured as "In Position (static)" the pattern should not change when you touch it with the yellow cable unless you activate that output at the same time via the transmitter. If you don't do that it seems that output 5 is always on GND potential, which would indicate a fault in the USM.

That being said do you use a toggle or momentary switch for output 5?

If momentary check output 5 by connecting a LED (with resistor) - does it always lit up or can you switch it on/off via the transmitter?

If the output is not in order try another one.

There is also the possibility that your light bar doesn't like that the output 8 does not provide a true GND / 0V potential (more like 0.5V), so you may need to consider using a relay to switch on/off the light bar.
Antworten