Die Suche ergab 6 Treffer
- So 24. Sep 2023, 20:22
- Forum: FAQ
- Thema: Hilfe, mein Nautic-/Multiswitchmodul funktioniert nicht
- Antworten: 31
- Zugriffe: 74496
Re: Hilfe, mein Nautic-/Multiswitchmodul funktioniert nicht
Hi Rascal, my apologies, you are correct, this is indeed the Boat 'n Truck transmitter, I made the mistake of assuming they are basically the same due to having the same exterior. The multimodule signal filter is available from Wetronic (they are a Beier distributor in the Netherlands). I cannot pos...
- Fr 22. Sep 2023, 22:48
- Forum: FAQ
- Thema: Hilfe, mein Nautic-/Multiswitchmodul funktioniert nicht
- Antworten: 31
- Zugriffe: 74496
Re: Hilfe, mein Nautic-/Multiswitchmodul funktioniert nicht
Hmmm, that is very strange. I also don't know what causes the pulses. Maybe I need to switch the multiprop and multiswitch connections in the transmitter and see if maybe it is a fault in the transmitter board. Also, it could be that the programming in the transmitter is wrong, I will see what happe...
- Fr 22. Sep 2023, 00:11
- Forum: FAQ
- Thema: Hilfe, mein Nautic-/Multiswitchmodul funktioniert nicht
- Antworten: 31
- Zugriffe: 74496
Re: Hilfe, mein Nautic-/Multiswitchmodul funktioniert nicht
Hi, I know this is an old topic, but I have seen it linked a few times as a solution for people who experience difficulties with Nautic modules, so I think I'm still in the right place. I have a Robbe FC-16 with Robbe F1512 Multiprop and RO8084 Multiswitch modules. The Multiprop is set to channel 8 ...
- Mo 18. Sep 2023, 21:56
- Forum: Soundmodul USM-RC-3
- Thema: Help needed in connecting my sound module
- Antworten: 4
- Zugriffe: 4445
Re: Help needed in connecting my sound module
Hi Rascal, Thanks for your quick reply. Yes, I was already planning on using the negative wires for the ESC's as well, I did not write it on the schematic correctly. I wrote signal only because I am cutting the red wire, but of course the black wire should be connected as well. As for switching pin ...
- Mo 18. Sep 2023, 19:59
- Forum: Soundmodul USM-RC-3
- Thema: Help needed in connecting my sound module
- Antworten: 4
- Zugriffe: 4445
Re: Help needed in connecting my sound module
Thank you so much, your post has helped me understand how this module works! My preferred setup on the transmitter is as follows: Right stick (ch. 1 & 2): rudder and center throttle Twin Navy sticks (ch. 3 & 4): Throttle left and right Linear slider left (ch. 5): Volume control Linear slider...
- So 17. Sep 2023, 23:35
- Forum: Soundmodul USM-RC-3
- Thema: Help needed in connecting my sound module
- Antworten: 4
- Zugriffe: 4445
Help needed in connecting my sound module
Greetings everyone! I have a Beier USM-RC-3 that I am trying to connect all my electronics to, to run a RC conversion of an Italeri S-100 Schnellboot. I have a Robbe Futaba FC-16 Boat ’n Truck transmitter, that has been converted to 2,4Ghz, and has both a Robbe Multiswitch and a Robbe Multiprop modu...