Seite 1 von 1

Suddenly reset with IR and heavy load

Verfasst: So 21. Apr 2013, 16:15
von Leonard
I have build a heavy hauler with Servonaut engine and Servonaut E20 speedcontroller.
The USM-RC-2 is in Mix-mode.
Normally everything works fine, and I can drive the lorry until the the battery runs low and USM-RC-2 tells me that the voltage is under the limit, switch sound and output off.

If I use it to haul heavy stuff, the model drives still perfectly, the engine are strong, but after a short time (2-4 minutes) the USM-RC-2 suddenly resets.
I tried to use the diagnose-function, but it seems that it restes totally, the only record I can sse in diagnose is the few seconds after it stops. I cannot see what happened just before it make the reset.
I have tried different combinations, and it only happens then I have the IR-led connected to USM-RC-2 and heavy load on the trailer. If i remove the plug to the IR-led, it doesnot have any malfunction, and if I drive with an empty trailer nothing happens.
It makes no difference if the battery are fully loaded or if it is nearly empty.

I have changed the IR-led and even tried with a complete new USM-RC-2, it is exactly the same.

Very strange ... any clues on what to do ?

Re: Suddenly reset with IR and heavy load

Verfasst: Mo 22. Apr 2013, 11:18
von BEIER-Electronic Andy
Hallo Leonard,

ich vermute, dass die Spannung am Soundmodul irgendwann kurz zusammenbricht und dehalb der Prozessor dann einen Neustart macht. Bei hoher Last kann ein Fahrtregler schon mal kurze Spannungseinbrüche auf der Versorgungsspannung verursachen.

Ein paar Fragen:
Tritt das Problem auch auf, wenn Du ohne bzw. mit leisem Sound fährst?
Wie dick ist das Kabel von Akku zu Soundmodul?
Wird das SM-IR-16 im Anhänger über einen anderen Akku versorgt?

Du kannst mal versuchen einen Kondensator (Elko) mit ca. 1000µF direkt an den Klemmen X1/1 und X1/2 anzuschließen. Sollte das Problem tatsächlich von Spannungseinbrüchen kommen, müsste der Kondensator diese vermindern.

Re: Suddenly reset with IR and heavy load

Verfasst: Mo 22. Apr 2013, 11:30
von Leonard
It makes no difference if the sound is on or off.
I use 1 mm2 wire from the akku to the soundmodul.
There is a seperate akku in the trailer.

I will try with the condensator and if that not solves it, I will try with an ekstra Akku only to the the Soundmodul.

Re: Suddenly reset with IR and heavy load

Verfasst: Mo 22. Apr 2013, 21:03
von Leonard
I have now tried with a 2200uF condensator - it just made it reset a little sooner.
I have also tried with a seperate Akku for the Soundmodule - some thing, it resets a little sooner.
I can see, that the blue LED on the USM-RC-2 flickers a little just before the reset.

I can not figure out why it only happens with the IR-led plugged in. Does that single led use a lot of power ?

Re: Suddenly reset with IR and heavy load

Verfasst: Di 23. Apr 2013, 11:41
von BEIER-Electronic Andy
Mysteriös...

Durch die IR-LED fließen nur (je nach Versorgungsspannung) ca. 4-8mA. Aber dieser Strom kann eigentlich nicht das Problem sein, weil er viel zu klein ist, um so eine Störung auszulösen.

Zwicke mal bitte das braune Kabel (von dem 3-poligen Kabel) an der IR-Diode, direkt an dem schwarzen Stecker ab. Bzw. kannst Du den einzelnen Kontakt (mit dem braunen Kabel) auch aus dem Stecker rausholen, indem Du die kleine schwarze Lasche hochhebst und am Kabel ziehst.

Schicke uns auch per eMail mal bitte Deine Projektdatei und am besten auch alle Sounds, die Du in dem Projekt verwendest.