Seite 1 von 1
Gunsound
Verfasst: So 13. Sep 2026, 17:54
von Torbenkg
Hi
Is it possible to assign gunsound to a switch on the radio without a new cable from usm to receiver?
The motor sound starts when the throttle stick moves.
Thanks in advance
Torben
Re: Gunsound
Verfasst: So 13. Sep 2026, 21:05
von Rascal
Hello Torben,
you didn't provide much information to answer the question for your particular setup.
Please upload the configuration file (*.usm-rc-3) and describe briefly how many cables / channels are already connected between receiver and USM module and for what function they are used.
Re: Gunsound
Verfasst: So 27. Sep 2026, 11:46
von Torbenkg
No more channels are avalible. But perhaps is it possible to play a gunsound every 20sec in flight. But not under start up and spool down. Is that possible to make in the Beier module?
Thanks in advance
Torben
Re: Gunsound
Verfasst: So 27. Sep 2026, 12:15
von Rascal
Hello Torben,
Torbenkg hat geschrieben: ↑So 27. Sep 2026, 11:46No more channels are avalible. But perhaps is it possible to play a gunsound every 20sec in flight.
But not under start up and spool down. Is that possible to make in the Beier module?
I don't understand the part in bold.
Generally you can play a sound repetitively using the following methods:
- Create a soundfile with the gun sound followed by silence for the desired time (e.g. 20 sec) and select the "Loop / immed. stop" option for the sound slot. Use function "Additional sound X" to play the sound.
- Make a
Function sequence with option "Loop / immed. stop" that plays the sound and then pauses for the desired time repeatedly. Use function "Function sequence X" to play the sound.
However in both cases you need to somehow start the function, so it would really help if you upload the file.
Also please state how you start the fight.
Re: Gunsound
Verfasst: So 27. Sep 2026, 13:06
von Torbenkg
It just mean that gunsound must not be activated on the ground. The bold type was a mistake
The sound starts when I give throttle and the rotor starts spinning. And that works fine now.
I have attached the file
Re: Gunsound
Verfasst: So 27. Sep 2026, 20:29
von Rascal
Oh, it's a helicopter. Now it makes more sense.
Some ideas:
- Prop #4 area D "Long in position (memory)" is not assigned with a function so you could add an additional sound or function sequence there, see my previous post.
- Sacrifice one of the additional sounds on Prop #3 or #5, i.e. replace the sound file with the gun sound file.
- Configure a random sound. You can specify that the sound will only play when a) in motion and b) when the engine sound is on.
Re: Gunsound
Verfasst: So 27. Sep 2026, 20:44
von Rascal
That being said I just noticed that Prop #4 has been assigned with several functions "Output X" but no output is configured.
Anyway, you can also use any free output to trigger a function sequence via the engine sound:
- Create a function sequence as described above (Configuration > Function seq. > Sequence X)
- Use a wire to directly connect a free output (e.g. output 16) with a free input (e.g. input X1/3)
- Define Output 16 as "Static (on or off)" (Configuration > Outputs > Outputs)
- Assign function "Function sequence X" to the input (Configuration > Inputs) - do not select "Memory"
- Enable Output 16 in the Engine sound tab for FG1 normal and FG2 normal
This way output 16 will become active whenever FG1 normal or FG2 normal is played, triggering the function sequence via the input X1/3. The function sequence then plays the gun sound repetitively as long as the FG is played.
Re: Gunsound
Verfasst: Di 29. Sep 2026, 17:50
von Torbenkg
I´m not sure that I understand what you suggest.
If I just make it simple with one single shot in the middle of the flight how can I do it then?
Thanks

Re: Gunsound
Verfasst: Di 29. Sep 2026, 22:11
von Rascal
Well, there are 4 options to choose from but this will probably be the easiest if you don't want to trigger the sound manually:
Configure a random sound. You can specify that the sound will only play when a) in motion and b) when the engine sound is on.
Relevant tabs:
Random sound
Configuration > Random sounds
See also the
manual on pages 41 and 76
Re: Gunsound
Verfasst: So 4. Okt 2026, 09:16
von Torbenkg
Thanks. It works now
