Seite 1 von 1

Product identification needed.

Verfasst: Di 25. Aug 2026, 21:56
von Cor
I am new here, as I never had any Beier item in my models, but that has now changed, because I have acquired an older truck model, which has not been used much and is in good shape. It is fitted with the following components
UFR-1230 V1-10
USM-RC-2 The sound module. There is no identification on this item, but I have search the site and this is my conclusion based on the published pictures.
Then, there is an small print, which I show in the pictures below, and I need to know what this is, and what the type number is, then I can probably find the documentation here too
Pictures:
20260822_142355.jpg
20260822_142355.jpg (2 MiB) 605 mal betrachtet
20260822_142521.jpg
20260822_142521.jpg (2 MiB) 605 mal betrachtet
20260825_155020.jpg
20260825_155020.jpg (2 MiB) 605 mal betrachtet
Reverse side; the number on this solder side is: 190306

Could you tell me what this is, assuming it is also a Beier PCB?
Thanks
Cor

Re: Product identification needed.

Verfasst: Di 25. Aug 2026, 23:08
von Rascal
Hello Cor,

I do not know if this module was made bei Beier but it looks like a 2-channel RC switch module, i.e. connection to the receiver on the right and two switched outputs (A1 & A2) on the left. The outputs seem to switch GND "-" (open collector). If you can identify T1 and T2 it may help to be sure.

The jumper probably selects between momentary and memory function. Just guessing here though I am sure the jumper must be set either to C-BR or C-SC (C = common), not open as shown.

You can try to connect the module to a receiver channel with the brown wire of the patch cable facing to the lower edge of the PCB in picture 1 and 2 (top side view). Connect a LED with a series resistor between an external battery+ and A1 (or A2), and "-" with external battery-.

Use a channel with a stick on the transmitter and see what happens when you move the stick. Try the 2 options for the jumper setting.

Re: Product identification needed.

Verfasst: Mi 26. Aug 2026, 07:10
von BEIER-Electronic Andy
The module does not come from us.

Re: Product identification needed.

Verfasst: Mi 26. Aug 2026, 12:46
von Cor
Thanks Rascal and Andy!
The transistors are both CTBC 337-25 LS
And I think it is indeed a switching module as the seller wrote me it was installed to energy 2 rotating beacons on the truck cab, but no connections known. Indeed there is a jumper, which I removed for clarity on the picture I took.
However, the 'rotating light' does not rotate, it is a simple LED which lights up when connected to a powersource, so it probably just flashes when connected to this print. The cable to the receiver has 2 sets of input pins, which are in parallel on the PCB, but seems strange, since you are not supposed to connect 2 receiver outputs together.. I thought

I 'll go ahead with testing this as you suggested
Thanks for your assistance
Cor

Re: Product identification needed.

Verfasst: Mi 26. Aug 2026, 14:54
von Rascal
Hello Cor,
Cor hat geschrieben: ↑Mi 26. Aug 2026, 12:46The transistors are both CTBC 337-25 LS
Ok, that's a NPN transistor and it switches GND. Which is what most RC modules do.
You can connect a load with a continuous current draw of 500-600mA (some safety margin included) to each output.
The cable to the receiver has 2 sets of input pins, which are in parallel on the PCB, but seems strange, since you are not supposed to connect 2 receiver outputs together.. I thought
You are correct but you can use the 2nd set to connect another module to the same receiver output since the 2 sets of pins work like a Y-cable.

Re: Product identification needed.

Verfasst: Do 27. Aug 2026, 13:59
von Cor
Hi Rascal, thanks for the info, I have connected this print on a separate receiver, and connected also a 4,8V battery and the 'rotating beacons' but no light, changed the jumper, but still nothing. Did a few other test and came to the conclusion that this item is defective, as I get no power on the output pins.
Will find something else, if only with a flashing LED in series on the output of a switching 'relay.
Thanks again for your help, I do appreciate this!
Cor