Seite 1 von 1
sound falls out often
Verfasst: Sa 15. Sep 2012, 11:58
von nickeles
Hello i finaly installed the module in my truck but i noticed that when i start it up with the nautic module swicht that it starts up and then falls out with no touching the switch
i have installed everything correctly and programmed it to nautic , even with error correction
it does this a few times and then it stays on sometimes it takes 4 to 5 times to start ...
could it be interference ????
hope that someone knows what to do maybe its simple solution
thnx Nik
Re: sound falls out often
Verfasst: Mo 17. Sep 2012, 07:57
von BEIER-Electronic Andy
Hello Nik,
what transmitter do you use?
Flashes the blue LED regularly?
Re: sound falls out often
Verfasst: Mo 17. Sep 2012, 15:50
von nickeles
hello ,
i use a robbe fc16 truck and boat the new version with servonaut 2,4 gigh system and the robbe multiswitch module
the bleu light flashes reguraly i use switch 1 up with memory on the robbe switch module to start the truck sound
when it starts it runs on idle and then after a short time it turns off then i switch it on again and sometimes its stayes on and works perfectly and sometimes its goes of again
most of the times after 3 or 4 times starting the engine sound it stays on and then works perfectly
maybe the wires are to close to each other ???
best regards Nik
Re: sound falls out often
Verfasst: Di 18. Sep 2012, 07:34
von BEIER-Electronic Andy
Servonaut 2,4GHz should be normaly no problem... Please try to bind transmitter and receiver again.
If this not works, then please try the integrated diagnosis function of the USM-RC-2:
- Open the Sound-Teacher and go to "Configuration" -> "General".
- Activate the option "Record diagnosis data on SD card".
- Save your project data onto SD card.
- Start the sound and wait until the problem happens.
- Wait 10 more seconds.
- Pull out the SD-Card.
- Now you will find a file "DIAGNOSE.DAT" on the SD card. Send this file via eMail to us.
Re: sound falls out often
Verfasst: Di 18. Sep 2012, 15:50
von nickeles
hello beier electroninc
i made a dat file and send it to your email
i noticed that on the sound module the blue light flashes reguraly a bit fast but reguraly but i noticed also that the red light also shined thru the flashing blue light
anny way maybe you can see something on the file i send to you
thnx best regards Nik
Re: sound falls out often
Verfasst: Mi 19. Sep 2012, 08:02
von BEIER-Electronic Andy
When the diagnosis is activated, the red LED indicates the recording of the diagnosis-data. When you deactivate the diagnosis function, the red LED should be off.
Ok, we looked into your DIAGNOSE.DAT... But the length of the data is only 10s long (and the sound is all the time off).
The firmware overwrites an every restart of the program the old diagnosis file. This means, when your sound goes off, the module probably has done a restart.
When the motor sounds goes off, goes it "hard" off, or plays the "engine stop sound" also?
Re: sound falls out often
Verfasst: Mi 19. Sep 2012, 09:28
von nickeles
Hello thnx for looking in to it so fast
when the egine sound stops it stops with the egine stop sound as i said sometimes it happens 3 times sometimes 2 times ....
the switchted that i assingned to start and stops engine sound i also programed it with the memmory on
best regards Nik
Re: sound falls out often
Verfasst: Mi 19. Sep 2012, 10:28
von BEIER-Electronic Andy
If the engine stop sound plays, then this contradicts the theory of a software restart...
Please record a DIAGNOSE.DAT again.
Have you tried to assign an other switch with the function "Engine sound on/off"?
Re: sound falls out often
Verfasst: Do 20. Sep 2012, 11:40
von nickeles
thnx for the help
you were right the problem is in the multiswitch i assinged the start and stop to another switch and no problem
i assinged air horn to switch 1 and the horn goes off sometimes unwanted so i now for sure the problem is switch one
i leave out switch one and wil check that later for now everythings works just fine !
verry happy with the module
thnx for the help