Seite 1 von 1
EMS 16G did not work well with Graupner FM4014
Verfasst: Mo 26. Jan 2026, 12:47
von Pelican32
I recently bought EMS 16G to install in the left empty slow of my Graupner FM4014 with an existing 4108 Nautic module in the right slow of the transmitter
When I checked the voltage at the output of the Nautic 4149 receiver module I found :
When the switches of the EMS are up :
+6volts on red/black wires
+6V on orange/black
0V on red/orange
When the switches are down : O Volts on all wires !!
I expected + 6Volts on red/orange ( with is the case using the Graupner 4108 Nautic module with 4149 receiver module.
Any idea about this issue ?
Thank you[*]
Re: EMS 16G did not work well with Graupner FM4014
Verfasst: Mo 26. Jan 2026, 13:42
von BEIER-Electronic Andy
Hello,
I'm afraid I don't understand exactly where you measured these voltages.
Graupner no. 4149 appears to be a Y-cable? Do you mean part number 4159?
What kind of module do you want to control with the EMS-16-G?
Re: EMS 16G did not work well with Graupner FM4014
Verfasst: Mo 26. Jan 2026, 14:10
von Pelican32
Thank for your Quick answer.
The configuration is as follow:
FM4014 top right slot Graupner 4108 connected on slot 6 inside the 4014 trasmitter
FM4014 top left slot EMS 16 G connected on slot 7 inside the transmitter using the 3 wires câble
I used 2-16K Graupner 4159 as a Nautic decoder throught of course a. FM receiver
On the 4159 Graupner module I powered it with 6V NiMh battery
I plugged Graupner relay module 3754/2 ( single 3 wires câble) on each output of the Graupner 4159 décoder.
When I switched up EMS 16G it is OK ( 1 relay of the 3754 is workng fine) but when I switched down nothing happened.
This behavior is not the same with 4108 module : when I switched down the second relay is running.
I did the same test without relay module connected on the décoder and I measure the voltage on the 3 pins connectors (x8) of the décoder and the results are what I described on my first post.
Re: EMS 16G did not work well with Graupner FM4014
Verfasst: Mo 26. Jan 2026, 14:28
von BEIER-Electronic Andy
I was afraid of that. You can't control a Graupner decoder with the EMG-16-G.
The EMS-16-G uses a completely different protocol and can only control our following modules:
- Sound speed controller SFR-1, SFR-1-D and SFR-1-HL
- Sound module USM-RC-2, USM-RC-3 and USM-HL-2
- Speed controller UFR-1230 and UFR-1230-D
- Switching module RC-SM-16
Re: EMS 16G did not work well with Graupner FM4014
Verfasst: Mo 26. Jan 2026, 15:04
von Pelican32
OK understood !. Many thanks
Is there a notice to use the RC SM 16module with FM4014 ? Wiring , warning, compatibility with the existing 4108 already used ?
Does it means the RC SM16 should be plugged on slot 7 of the FM receiver ( if I m using slot 7 inside the FM4014 for the EMS 16.
Regards
Re: EMS 16G did not work well with Graupner FM4014
Verfasst: Mo 26. Jan 2026, 15:10
von BEIER-Electronic Andy
We are not aware of any problems with that.
Yes, the RC-SM-16 is then plugged into slot 7 of the receiver.