EMS-16-G in a FlySky FS-i6X
Verfasst: Di 19. Nov 2024, 20:21
So I've been silent a while. My truck project went on hold when dad died and mom got cancer.
Mom is doing much better now and I've had a chance to dig back into these side projects again.
I've acquired a Flysky FS-i6X, and in converting the left stick to self-centering, I noticed all the shoulder switches and the two dials are all connected with three-pin JSC plugs.
I've got the tools and supplies to crimp a new plug onto the EMS-16-G cable, so I can unplug and remove one of the two POT dials and feed the multiswitch cable through the resulting hole.
I just wonder if anyone has done this conversion already, even if they cut and soldered the wires, as getting a sneak peek at what wire goes to what pin in the plug would be very helpful. I know one is negative supply, one is positive ground, and one is signal, but right now I'm not sure which is which.
I don't want to go poking at wires with a multimeter I don't fully understand and possibly fry everything, without asking if someone already knows the answer.
As a side question, I have three trailers in the works, connected via the LM-IR-16-4 unit. I've got the signals for lights working reliably through the kingpin and coupler on a bench test setup, in that the signal is solid when coupled but there's no signal bleed activating uncoupled units.
However I have a different landing leg mechanism for all three: A set of Lesu screw legs, a Tamiya powered leg system, and a worm and segment gear to make a DGN gooseneck bend up and down to ground the float.
If the Multiswitch in the FS-i6X works, I'll have one POT dial free to work with.
I am wondering, just yes or no, if the soundteacher can use the multiswitch to change that dial between being a volume control, and powering the landing gear either through the motor posts on the LM module or a separate ESC on a Servo channel.
If 'no', I'm pretty sure the system can use one of the Multiswitch switches as 'Volume +/Volume -' from what I've read in the manuals.
Mom is doing much better now and I've had a chance to dig back into these side projects again.
I've acquired a Flysky FS-i6X, and in converting the left stick to self-centering, I noticed all the shoulder switches and the two dials are all connected with three-pin JSC plugs.
I've got the tools and supplies to crimp a new plug onto the EMS-16-G cable, so I can unplug and remove one of the two POT dials and feed the multiswitch cable through the resulting hole.
I just wonder if anyone has done this conversion already, even if they cut and soldered the wires, as getting a sneak peek at what wire goes to what pin in the plug would be very helpful. I know one is negative supply, one is positive ground, and one is signal, but right now I'm not sure which is which.
I don't want to go poking at wires with a multimeter I don't fully understand and possibly fry everything, without asking if someone already knows the answer.
As a side question, I have three trailers in the works, connected via the LM-IR-16-4 unit. I've got the signals for lights working reliably through the kingpin and coupler on a bench test setup, in that the signal is solid when coupled but there's no signal bleed activating uncoupled units.
However I have a different landing leg mechanism for all three: A set of Lesu screw legs, a Tamiya powered leg system, and a worm and segment gear to make a DGN gooseneck bend up and down to ground the float.
If the Multiswitch in the FS-i6X works, I'll have one POT dial free to work with.
I am wondering, just yes or no, if the soundteacher can use the multiswitch to change that dial between being a volume control, and powering the landing gear either through the motor posts on the LM module or a separate ESC on a Servo channel.
If 'no', I'm pretty sure the system can use one of the Multiswitch switches as 'Volume +/Volume -' from what I've read in the manuals.