Seite 1 von 2
UFR1230 disconnecting from USM3
Verfasst: Mo 25. Sep 2023, 08:58
von minimivic
I have 2 linear actuators power by 12v through 2 x MFR1210 speed controllers.
These are connected to the USM RC3 on servo outputs 2 and 3
Radio master TX16s via SBUS to control the USM RC3 functions
Every so often one of the 1210's will stop working its random and can be either one of them, turning off the model and then back on again fixes the issue.
This is the actuator
https://www.amazon.co.uk/EYPINS-Actuato ... 9hdGY&th=1
Any ideas what I should look for,
Re: UFR1230 disconnecting from USM3
Verfasst: Mo 25. Sep 2023, 09:13
von Rascal
Hello,
assuming your receiver is powered by a BEC or another speed controller's BEC you need to disconnect the red wire from the MFR-1230 servo cable (remove the red wire from the servo plug and isolate).
You can also add a 47 to 100nF capacitor as suppressor between the wires of the actuators, and perhaps some ferrite rings / ferrite beads on the cable to the actuators.
Re: UFR1230 disconnecting from USM3
Verfasst: Mo 25. Sep 2023, 15:19
von minimivic
Rascal,
Yes alternative speed controller powers the receiver.
Both 1210's have the red wires disconnected and made safe.
will get some capacitors to try? But why is this needed?
I have ferrite coli and beads now so can easily eat that.
Re: UFR1230 disconnecting from USM3
Verfasst: Mo 25. Sep 2023, 17:59
von Rascal
Hello,
minimivic hat geschrieben: ↑Mo 25. Sep 2023, 15:19will get some capacitors to try? But why is this needed?
Brushed motors require supression capacitors because of brush sparking which will cause electromagnetic interference, not just to the model itself but it may also impact other devices in the vincinity.
Normally this is done with 3 capacitors installed as close as possible to the motor, see
here (sorry, German only).
Since you can't fit any between the terminals and the motor case I suggest you insert at least the one between the terminals, or in case of the actuator between the two wires.
Re: UFR1230 disconnecting from USM3
Verfasst: Mi 27. Sep 2023, 15:29
von minimivic
What voltage capacitor should I get?
Electrics like this are not my strong point. I’ve seen 10v and 16v so was going for 16v.
Thanks
Re: UFR1230 disconnecting from USM3
Verfasst: Mi 27. Sep 2023, 17:34
von Rascal
Hello,
minimivic hat geschrieben: ↑Mi 27. Sep 2023, 15:29What voltage capacitor should I get?
Electrics like this are not my strong point. I’ve seen 10v and 16v so was going for 16v.
for suppression use
ceramic capacitors only, they have a rating of 50V to 100V.
They look like this (color may vary depending on the manufacturer):
https://elteile.de/passive-bauelemente/ ... ondensator
https://www.ebay.de/itm/252183902976
Re: UFR1230 disconnecting from USM3
Verfasst: Fr 13. Okt 2023, 11:04
von minimivic
Lots of testing a still same problem.
Setup is 12v input
3 x MFR1210 speed controllers
2 are operating
https://www.amazon.co.uk/EYPINS-Actuato ... 9hdGY&th=1 which are specified at 4amp max
1 is operating a small linear actuator
https://www.ebay.co.uk/itm/314798635113 ... R8Dml4TlYg
I have tried:
a separate power supply no change
Changing the pwm from the USM RC3 (servo outs 1,3,4) to direct and no change
Added capacitors as above parallel across the + and - terminal of the actuator.
Added ferrite coils and chokes.
Keep getting the same problem when 2 or more are used at the same time one or more of them will stop working and beep 3 times.
Individually I can use them until I am bored and they work just fine
Re: UFR1230 disconnecting from USM3
Verfasst: Fr 13. Okt 2023, 13:54
von Rascal
Hello,
does the MFR get hot when it's moving the actuator?
Do you hear any beeps from the MFR when the actuator stops working? If yes, how often?
Re: UFR1230 disconnecting from USM3
Verfasst: Fr 13. Okt 2023, 14:16
von minimivic
Stopping happens pretty quickly so no heat build up.
At the end of the actuator travel I get 1 beep but it keeps working. when it stops working I get 3 beeps every 10 seconds like its short circuited.
Restart the model and all come back to life.
Re: UFR1230 disconnecting from USM3
Verfasst: Fr 13. Okt 2023, 20:01
von Rascal
In this case measure the actual current drawn by the actuators.