Seite 1 von 2

how to connect Vantage Lightbar

Verfasst: So 11. Mär 2018, 10:02
von Jimmy777
Hi. I have this lightbar https://www.verkerk-modelbouw.nl/vantag ... ranje.html
and there is one red cable one black and one yellow.

I know there will be different possibilites fixing this but anypone knows a good way?
I have 2 outputs free on the usm-2.

Re: how to connect Vantage Lightbar

Verfasst: So 11. Mär 2018, 17:01
von Rascal
So what does the manual say how to connect the wires and how to switch the pattern?
If you can provide this information perhaps we can help.

Re: how to connect Vantage Lightbar

Verfasst: So 11. Mär 2018, 18:09
von Jimmy777
The red wire is for plus and the black is ground. The yellow one is for changing the different patterns of the light.

I´ve tried having the black and yellow in two different outputs and the red to plus. I can make it glow and change one pattern only but thats it.

Re: how to connect Vantage Lightbar

Verfasst: So 11. Mär 2018, 18:40
von Rascal
You didn't answer my question - what does the manual say about the wires and how to switch the pattern?

Is it possible that the wires should be connected directly to the receiver (just like a servo)?

Re: how to connect Vantage Lightbar

Verfasst: So 11. Mär 2018, 18:52
von Jimmy777
Ok, sorry I missunderstood you a bit.

Connect the red cable to constant plus.
Connect the black cable to a radio controlled switch connected to the minus in your model
Connect the yellow cable to the minus by using a manual or radio controlled switch. This allows you to change the programmed light patterns every time you establish a contact to the minus. The light bar will always turn on again, functioning in the last shosen light flash pattern. This product offers 34 piece pre programmed flash patterns.

This is what it says on the instructions on the box with the lightbar. I hope this is what you nedeed.

Re: how to connect Vantage Lightbar

Verfasst: So 11. Mär 2018, 22:06
von Rascal
Ok, that helps, thanks. Try this:

Connect red to plus and black to output 1 (for example). Output 1 will be configured as "Static (Sound Prop)".
Connect yellow to output 2 (for example). Output 2 will be configured as "Static (Sound Prop)".

Now there are two options:
1. Assuming you use the proportional channels with sticks or momentary switches (1)-0-(1) to control the outputs:
Configure e.g. Prop #3 area A as "Long in position (memory)". This will be used to switch on/off the light bar.
Configure e.g. Prop #3 area D as "In position (static)". This will be used to switch the pattern.

2. Assuming you use the proportional channels with toggle switches 1-0-1 to control the outputs:
Configure e.g. Prop #3 area A as "In position (static)". This will be used to switch on/off the light bar.
Configure e.g. Prop #4 area A as "In position (static)". This will be used to switch the pattern.

Use the stick or switch on the transmitter to activate output 1 first; if you use a toggle switch (option 2. above) leave it in the "on" position. The lightbar should now flash with the last pattern selected.
Then use the stick or switch (different switch with option 2. above!) to change the pattern; if you use a toggle switch bring it back into "off" position immediately. The pattern should change every time you push the stick to position D or push/toggle the switch (off > on > off).

To switch the lightbar off use the stick or switch of Prop #3.

Re: how to connect Vantage Lightbar

Verfasst: So 18. Mär 2018, 18:52
von Jimmy777
Ihave now tried using the proportional channels with sticks and have used:

Red to plus
black to output
yellow to another output.

I configured them like it says and I can get the light bar to start and then it glows and move one light at a time and moves around the whole lightbar.
If I change the stick so I change the pattern and then all light in the lightbar is glowing all the time. If I try again change pattern it goes back to the first one.

I even tried changing the outputs with static and memory but its the same on both.

I am sure I am missing something and have been reading what you wrote several times but still can´t figure out what I do wrong.

At least there is light on it so it´s working at least :)

Re: how to connect Vantage Lightbar

Verfasst: So 18. Mär 2018, 20:06
von Rascal
Can you upload your project file (*.usm)?

Which option are you using? (see my post above)

Re: how to connect Vantage Lightbar

Verfasst: So 18. Mär 2018, 20:43
von Jimmy777
Im going for option 1

Will you need the sound files or is this file enought?

Re: how to connect Vantage Lightbar

Verfasst: So 18. Mär 2018, 23:26
von Rascal
No need for the sound files, that file is sufficient.

Not sure this is because I am currently using the sound teacher demo (based on version 1.40d) but I can not see which output you have configured for the black and yellow cables?