I have a rotorblink on output 10.
Output 11 and 12 are used by sequence 1 to make a blitzwarnblink.
On the trailer I have an IR - flasher.
Works fine, but i have to use 3 different places on the Prop-channels to turn it all on/off and they shall allways turn on/off at the same time.
Suggestion:
Make some groups, where I can collect several outputs and functions - and make it possible to turn on/off a hole group with one move in the prop-channel or EKMFA
Switch more with one
Switch more with one
Feel free to answer in german, I can read it but not write it.
Leonard - DK
Leonard - DK
- marco polo
- Beiträge: 92
- Registriert: Di 26. Okt 2010, 20:45
- Wohnort: holland
- Kontaktdaten:
Re: Switch more with one
hi leonard
i think i have a little solution for you
if you take output 10
and put the output 10 in to sequence 1
an the for every step in the sequence for output 10 make the output 100%
then it turns on when you activate sequence 1
and off when deactivated whit one switch i hope it is helpfull
greeting from the netherlands
marco polo
i think i have a little solution for you
if you take output 10
and put the output 10 in to sequence 1
an the for every step in the sequence for output 10 make the output 100%
then it turns on when you activate sequence 1
and off when deactivated whit one switch i hope it is helpfull
greeting from the netherlands
marco polo
groeten uit Nederland,
Niets is zeker, en zelfs dat niet.
Niets is zeker, en zelfs dat niet.
Re: Switch more with one
I have tried this, but as I remember it, it makes a little flicker, every time it starts from top again.
And it does not solve the problem with switching the IR-Flasher on ...
And it does not solve the problem with switching the IR-Flasher on ...
Feel free to answer in german, I can read it but not write it.
Leonard - DK
Leonard - DK
- marco polo
- Beiträge: 92
- Registriert: Di 26. Okt 2010, 20:45
- Wohnort: holland
- Kontaktdaten:
Re: Switch more with one
ok leonard
try this one
i use similar for a rotating beacon whit four outputs and yes this does not solve the problem for the ir flasher
but you need 1 switch less to operate
gr marco polo
try this one
i use similar for a rotating beacon whit four outputs and yes this does not solve the problem for the ir flasher
but you need 1 switch less to operate
gr marco polo
groeten uit Nederland,
Niets is zeker, en zelfs dat niet.
Niets is zeker, en zelfs dat niet.
- BEIER-Electronic Andy
- Administrator
- Beiträge: 4557
- Registriert: Mi 17. Dez 2008, 07:37
Re: Switch more with one
Über einen "Eingang" gleich 2 Funktionen auszulösen ist ja leider momentan nicht möglich. Das wäre zwar theoretisch machbar, jedoch ein sehr großer Aufwand, weil da sehr viel umprogrammiert werden müsste. Ich haben den Vorschlag aber mal notiert und vielleicht können wir das irgendwann mal umsetzen.
Die Idee von marco polo das mit einer Ausgangssequnz zu lösen ist aber sehr gut! Bei der V1.10 gibt es jedoch einen kleinen Bug, wenn im 1. Schritt die Dauer auf 0,1s eingestellt ist. Dann wird aus der Zeit 0,2s. Dieser Fehler wird im nächsten Update (wird wohl in den nächsten Tagen kommen) behoben. Dann gibt es auch wieder Zeiten mit 0,01s Auflösung
Aber auch für diesen Bug hat marco polo die Lösung: Einfach im 1. Schritt einen "Leerschritt" einfügen und die Schleife erst im 2. Schritt starten zu lassen.
Die Idee von marco polo das mit einer Ausgangssequnz zu lösen ist aber sehr gut! Bei der V1.10 gibt es jedoch einen kleinen Bug, wenn im 1. Schritt die Dauer auf 0,1s eingestellt ist. Dann wird aus der Zeit 0,2s. Dieser Fehler wird im nächsten Update (wird wohl in den nächsten Tagen kommen) behoben. Dann gibt es auch wieder Zeiten mit 0,01s Auflösung
Aber auch für diesen Bug hat marco polo die Lösung: Einfach im 1. Schritt einen "Leerschritt" einfügen und die Schleife erst im 2. Schritt starten zu lassen.