Forum,
How can I connect one or two Graupner Nautic-Expert-modul's Nr. 4108 to a USM-RC-3 module?
swift13
connecting nautic moduls to usm-rc-3
Re: connecting nautic moduls to usm-rc-3
Hello swift13,
connect the receiver channel corresponding to the nautic module/s to Prop #3 (X2/3) and/or Prop #4 (X2/4) using a servo patch cable.
See also the table in the manual on pages 9 & 21, and for more details pages 44 to 45 and 76.
connect the receiver channel corresponding to the nautic module/s to Prop #3 (X2/3) and/or Prop #4 (X2/4) using a servo patch cable.
See also the table in the manual on pages 9 & 21, and for more details pages 44 to 45 and 76.
Re: connecting nautic moduls to usm-rc-3
Hello Rascal, at the nautic module 4108 is't not possible to connect a patchy cable
on a 4108 module is a lead connected with a female connector of 4 pins
which nautic modul are you refering to ?
on a 4108 module is a lead connected with a female connector of 4 pins
which nautic modul are you refering to ?
Re: connecting nautic moduls to usm-rc-3
Hello,
if you need to know how to connect the 4108 in the transmitter please refer the Graupner documentation of your transmitter and the nautic module.
Once installed the module will be assigned/connected to a specific channel. This channel you need to use at the receiver for connecting the USM-RC-3 with a patch cable.
No nautic module (like 4159) is required between receiver and USM-RC-3.
if you need to know how to connect the 4108 in the transmitter please refer the Graupner documentation of your transmitter and the nautic module.
Once installed the module will be assigned/connected to a specific channel. This channel you need to use at the receiver for connecting the USM-RC-3 with a patch cable.
No nautic module (like 4159) is required between receiver and USM-RC-3.
Re: connecting nautic moduls to usm-rc-3
Rascal,
I know that, hi had a graupner expert modul 6014 with 3 of those modules inside
But all where broken and behind repair .
Now I have a new transmitter Flysky Paladin PL 18EV DE, with the sound module USM-Rc-3
And in the manual ( of the USM-RC-3 ) theres a sugestion that you could connect one or two nautic modules 4108
on them
Anyway thank you for your remarks
swift13
I know that, hi had a graupner expert modul 6014 with 3 of those modules inside
But all where broken and behind repair .
Now I have a new transmitter Flysky Paladin PL 18EV DE, with the sound module USM-Rc-3
And in the manual ( of the USM-RC-3 ) theres a sugestion that you could connect one or two nautic modules 4108
on them
Anyway thank you for your remarks
swift13
Re: connecting nautic moduls to usm-rc-3
With the Paladin PL18 EV you don't need the nautic modules anymore, you could just use sBus like I do.
It is, in my opinion, the easier and simpler solution for you don't need any extra modules on your transmitter.
The option to connect nautic modules to the USM-RC-3 is for when your transmitter has them built in (or at least the option to) but with iBus and sBus you can do the same things the nautic module would do, you're just using the built in switches, buttons etc. your transmitter already provides.
For example, SWD on my PL18 EV is acting as light switch - lever up = light +, lever down = light -
I linked SWD in my PL18 EV to Channel 10.
These are screenshots from my SFR-1, but it works the same with the USM-RC-3.
It is, in my opinion, the easier and simpler solution for you don't need any extra modules on your transmitter.
The option to connect nautic modules to the USM-RC-3 is for when your transmitter has them built in (or at least the option to) but with iBus and sBus you can do the same things the nautic module would do, you're just using the built in switches, buttons etc. your transmitter already provides.
For example, SWD on my PL18 EV is acting as light switch - lever up = light +, lever down = light -
I linked SWD in my PL18 EV to Channel 10.
These are screenshots from my SFR-1, but it works the same with the USM-RC-3.
Zuletzt geändert von Hasi am Sa 4. Nov 2023, 10:58, insgesamt 1-mal geändert.
Grüße,
Stefan
Diverse RC-Cars (On- & Offroad), Trucks im Tamiya-Maßstab
Stefan
Diverse RC-Cars (On- & Offroad), Trucks im Tamiya-Maßstab
Re: connecting nautic moduls to usm-rc-3
Well, that's quite a different configuration then.
Yes (or two Beier EMS/NMS, two Robbe multiswitches or two CP/Mergen modules) but if you do not have a Graupner transmitter and not the 4108 modules why do you keep on asking about the 4108 !?And in the manual ( of the USM-RC-3 ) theres a sugestion that you could connect one or two nautic modules 4108
on them
As Hasi suggested you can use SBUS to reduce cables between receiver and the USM-RC-3, see also this video.
And this video shows you how to control up to 8 functions with 1 switch using the proportional channels. This configuration can also be combined with SBUS.