SFR-1 motor control
SFR-1 motor control
Hi now i have a small problem and i'm sorry even i looked through it all but no, i can't get the engine running forward but only backwards what i forgot to put up
Re: SFR-1 motor control
Hello,
did you do the Setup (Teaching Function) as per manual?
If yes, what is the status of the LEDs on the SFR-1 after that?
Furthermore please provide more details, including
- Make and model of the transmitter, receiver and battery (including voltage)
- Project-File (*.sfr)
did you do the Setup (Teaching Function) as per manual?
If yes, what is the status of the LEDs on the SFR-1 after that?
Furthermore please provide more details, including
- Make and model of the transmitter, receiver and battery (including voltage)
- Project-File (*.sfr)
Re: SFR-1 motor control
Hej
når jeg følger vejledningen så blinker lysdioden som forskrevet men den vil kun enden kører frem eller bak, og sender er en Taranes E9X og kører på 7,4 volt batteri modtager er en X8R med SBUS i og jeg vedhæfter lige min opsætning i Beier
når jeg følger vejledningen så blinker lysdioden som forskrevet men den vil kun enden kører frem eller bak, og sender er en Taranes E9X og kører på 7,4 volt batteri modtager er en X8R med SBUS i og jeg vedhæfter lige min opsætning i Beier
- Dateianhänge
-
- kroghejs.sfr
- (38.66 KiB) 110-mal heruntergeladen
Re: SFR-1 motor control
Hi,
thanks, I took a look at the configuration and have some questions:
1. Did you connect Prop #1 (X2/1) and Prop #2 (X2/2) to the receiver? If yes, what channel (gas, steering ...) are they matched to?
2. What do the status LEDs show when the gas channel is
a) idle
b) in forward
c) in reverse
Please include the state of all 3 LEDs (on, off, flashing fast, flashing slow ...)
thanks, I took a look at the configuration and have some questions:
1. Did you connect Prop #1 (X2/1) and Prop #2 (X2/2) to the receiver? If yes, what channel (gas, steering ...) are they matched to?
2. What do the status LEDs show when the gas channel is
a) idle
b) in forward
c) in reverse
Please include the state of all 3 LEDs (on, off, flashing fast, flashing slow ...)
Re: SFR-1 motor control
Hi
the authors aim
1. ch1. is X2 / 1 Gas
X2 / 2 is control
and touch the diodes of sound
green is constantly lit.
blue blinks fast
And they do what I do with the gas stick and the red does not light at all
the authors aim
1. ch1. is X2 / 1 Gas
X2 / 2 is control
and touch the diodes of sound
green is constantly lit.
blue blinks fast
And they do what I do with the gas stick and the red does not light at all
Re: SFR-1 motor control
Hi,
please try the following:
- Disable S-BUS
- Connect the SFR-1 only with the servo-cable X2/1 to the receiver gas channel
- Perform "Setup (Teaching Function)" of the SFR-1
Now try again - does this solve the problem?
please try the following:
- Disable S-BUS
- Connect the SFR-1 only with the servo-cable X2/1 to the receiver gas channel
- Perform "Setup (Teaching Function)" of the SFR-1
Now try again - does this solve the problem?
Re: SFR-1 motor control
it is not something that helps but can hardly use light and sound setup but then just use another speed controller but otherwise thanks for the help greeting from Denmark
Re: SFR-1 motor control
It would help to see if the problem is with S-BUS or something else.
Else make a diagnosis please (see pages 90-91 of the manual).
Else make a diagnosis please (see pages 90-91 of the manual).