Abend zusammen,
Sorry für mein Deutsch. Ich frage mich, ob es möglich ist, die folgende auf diesem Gerät zu tun.
Auf meinem Graupner Adolph Bermpohl möchte ich den Ton Einheit ein Geräusch bewirkt und Relais und Blitzen geführt zugleich für die hintere Tür mit einem robbe Multischalterzu aktivieren. beide werden über diese Relais-Board gesteuert werden .. . Ich habe diese Relaiskarte mit den robbe -Decoder in der Vergangenheit verwenden und sind groß.
http://www.ebay.co.uk/itm/5V-4-Channel- ... 0981814441
Vielen Dan
ist dies möglich,
Re: ist dies möglich,
Leider verstehe ich deine Frage nicht. Kannst du es auf Englisch schreiben?
Re: ist dies möglich,
Sorry I can read German better than I can write it (been many years)
what I would like to do on my Adolph Bermpohl is when I activate a switch on the robbe switch module for F16, the USM-RC plays a sound file but also to activate a relay to open the rear door (currently using servo and micro switches to start and stop the motor.)
Same for the recoverly drive unit.
And if possible have the lights flash.
The reason for this is to save on the amount of receiver channels used.
Thank you again.
what I would like to do on my Adolph Bermpohl is when I activate a switch on the robbe switch module for F16, the USM-RC plays a sound file but also to activate a relay to open the rear door (currently using servo and micro switches to start and stop the motor.)
Same for the recoverly drive unit.
And if possible have the lights flash.
The reason for this is to save on the amount of receiver channels used.
Thank you again.
Re: ist dies möglich,
Hello Dan,
if I understand your request correctly, you have a (3-position ???) switch on the F16 that stears the opening resp. the closing of the ramp. In addition to the ramp lights must flash and a sound must be played.
My solution fir this would be to create an arduino solution that scans the switch. If the switch is touched, the arduino starts 3 actions:
1. Pull one input channel on the USM-RC to play the sound
2. Start flashing the lights. The steering has to be done by the arduino board
3. Activate the relay to open/close the door
While the arduino is performing the action, the board must check if the switch is still touched and if the end switch is still open. If one of the checks is negative the action must be stopped.
In my opinion, the action can't be solved ckmlletely by the USM-RC.
if I understand your request correctly, you have a (3-position ???) switch on the F16 that stears the opening resp. the closing of the ramp. In addition to the ramp lights must flash and a sound must be played.
My solution fir this would be to create an arduino solution that scans the switch. If the switch is touched, the arduino starts 3 actions:
1. Pull one input channel on the USM-RC to play the sound
2. Start flashing the lights. The steering has to be done by the arduino board
3. Activate the relay to open/close the door
While the arduino is performing the action, the board must check if the switch is still touched and if the end switch is still open. If one of the checks is negative the action must be stopped.
In my opinion, the action can't be solved ckmlletely by the USM-RC.
Re: ist dies möglich,
thank you gismow.
at the moment it on a 2 position switch for door, but i was hoping to use my robbe 8 Chanel multi switch though the sound board, but this will work the same.
I have been looking into the arduino boards for a my submarine to control the piston tanks and few other items.
Many Thanks
Tim
at the moment it on a 2 position switch for door, but i was hoping to use my robbe 8 Chanel multi switch though the sound board, but this will work the same.
I have been looking into the arduino boards for a my submarine to control the piston tanks and few other items.
Many Thanks
Tim
Re: ist dies möglich,
Got it work how i wanted thanks and worked great.
but some how knocked it over and some how shorted it. the heat sink gets very hot but no sound . plugged it in to the pc and can see it responding on the test part of the software.
but some how knocked it over and some how shorted it. the heat sink gets very hot but no sound . plugged it in to the pc and can see it responding on the test part of the software.
- BEIER-Electronic Andy
- Administrator
- Beiträge: 4151
- Registriert: Mi 17. Dez 2008, 07:37
Re: ist dies möglich,
Sounds like a broken amplifier
You can ship the module to us and we'll check and repair it.
You can ship the module to us and we'll check and repair it.
Re: ist dies möglich,
Thank you, Will get pack up and in the post.